3. A simple shunted dc ammeter, using a basic meter movement with an internal resistance, R ==== 1,800 2, and a full-scale deflection current, Irsd = 100 μA, is connected into a circuit and gives a reading of 3.5 mA on its 5-mA range. This reading is checked by a recently calibrated dc ammeter which gives a reading of 4.1 mA. The implication is that the first ammeter has a faulty shunt on its 5-mA range. Calculate (a) the actual value of the faulty shunt; (b) the correct shunt for the 5-mA range.

3. A simple shunted dc ammeter, using a basic meter movement with an internal resistance, R ==== 1,800 2, and a full-scale deflection current, Irsd = 100 μA, is connected into a circuit and gives a reading of 3.5 mA on its 5-mA range. This reading is checked by a recently calibrated dc ammeter which gives a reading of 4.1 mA. The implication is that the first ammeter has a faulty shunt on its 5-mA range. Calculate (a) the actual value of the faulty shunt; (b) the correct shunt for the 5-mA range.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

diodes are identical ,Vr=50 mV, R=?
The single-phase half wave rectifier is suppling an (RL) load. Assume that power is equal to 1500 , where R=3Ω, a=π/6 and β=2π/3. find maximum voltage.
Answer the question quecly please Electrical Machines
True or False: A diode can be used as a voltage source.
Vs(t) = 50sin(20πt) All diodes are ideal.
4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?
1. How is the capacitor value here calculated? 2. Make a circuit analysis
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 1 V/cm. Determine the (i) amplitude of waveform Q (i) peak to peak value of waveform P. (ii)i frquency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. () Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (ii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Vs(t) = 50sin(20πt) All diodes are ideal.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) DI 14001 RL V onl O V 10 kN D2 IN4001 allle
The single-phase bridge rectifier of Figure below is required to supply an average voltage io of Vdc = 300 V to a resistive load of R = 15 2. Determine the voltage and current ratings of diodes and transformer. D₁ D₂ D3 D₂ www vo