3. A pair of bevel gear have a 1:1 velocity ratio, a pitch diameter of 8 in, a face of 1 % in and they rotate at 250 rpm. The teeth are 5 diametral pitch 14 % deg involute. These gears transmit 8 hp. Determine: A. the outside diameter of the gears B. the pitch line velocity of the gear C. the tangential force of the gear Ans. 8.28 in Ans. 523 fpm Ans. 504 lbs

3. A pair of bevel gear have a 1:1 velocity ratio, a pitch diameter of 8 in, a face of 1 % in and they rotate at 250 rpm. The teeth are 5 diametral pitch 14 % deg involute. These gears transmit 8 hp. Determine: A. the outside diameter of the gears B. the pitch line velocity of the gear C. the tangential force of the gear Ans. 8.28 in Ans. 523 fpm Ans. 504 lbs

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear 1 is the driving gear and transmits 50 kW power at 300 rpm to the gear train. The number of teeth on gears 1, 2, 3 and 4 are 30, 60, 25 and 50 respectively, while the module for all gears is 8 mm. Gears 2 and 3 are mounted on the same shaft. Gear 1 is rotating in the clockwise direction when seen from the left side of the page. The shaft is made of plain carbon steel 40C8 (Syt = 380 N/mm2) and the factor of safety is 2. Using maximum shear stress theory, estimate suitable diameter of shaft. 150 500 125 3 B1 B2
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5°. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: 1.5. The addendum of the gears in mm. 1.6. The contact ratio.
Please help with homework
Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D
no Qt+ A Compound gear train Consists of 6 gears. No of teeth : A B D E 60 40 35 28 50 30 shaft on another shaft. The Gears B $ C are on One while are gears Gear A drives B, gear gear c drives, gear s gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2z State advkitages of Cycloidal In volute profile as a gear tooth pnfile.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: 1.The length of a path of a recess in mm.2. The addendum of the gears in mm.
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. -20KW 7OKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O If segment Co is to be replaced ay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: a) The magnitude of the velocity of slip of gears in mesh. b)The maximum length of a path of the approach in mm c ) The length of a path of a recess in mm d) The addendum of the gears in mm e) The contact ratio.
The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears 40 teeth 490⁰ B 70 teeth 50 teeth
A pair of gears, having 43 and 22 teeth respectively, are rotating in mesh, the speed of the smaller being 1600 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 20° involute form, addendum length is 5 mm and the module is 3 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact.