3. A microprocessor has . .. address bus a. unidirectional b. bi-directional c. Both 4. Instruction queue allows up to . . of instruction code to be pre-fetched. a. 16 bits b. 6 bytes c. 6 bits 5. To activate the address bus or data bus in ADg-AD15 signal the. should be either logic 1 or 0. a. MN /MX b. RD c. ALE

3. A microprocessor has . .. address bus a. unidirectional b. bi-directional c. Both 4. Instruction queue allows up to . . of instruction code to be pre-fetched. a. 16 bits b. 6 bytes c. 6 bits 5. To activate the address bus or data bus in ADg-AD15 signal the. should be either logic 1 or 0. a. MN /MX b. RD c. ALE

Name: (B)- Choose the correct answer for the following questions1. Assume A
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: (B)- Choose the correct answer for the following questions1. Assume AL register 7FH, it would become.. after executed NEG AL instruction.a. 8FHb. 18Hс. 81H2. The unknown value for ????:BO00H=25000H physical address is ...a. 001A Hb. 1A00Hс. 100АН3.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

3. Describe data bus, address bus and control bus.
Assume that a RISC processor takes 2 microseconds to execute each instruction and that an I/O device can wait at most 1 millisecond before its interrupt is serviced. What is the maximum number of instructions that can be executed with interrupts disabled?
Computer architecture (Draw the circuit of a 1-bit register that can perform the x+y.z: R. € I. microprocess and retains the value in other cases. Note: R, represents 1-bit of the register and I, represents a 1-bit input.)
Q- Determine the correct and false sentences 1-8085up has 8 bits data bus and 16 bits address bus. 2- MEMR signal means that the data is transferred from memory to the microprocessor. 3-ALE signal is used to demultiplexing the data bus with the address bus. 4- NOP instruction is used for producing 4T delay.. 5- The ALU unit of 8085 up performs the arithmetical operations (addition, subtraction) only. 6- The Parity Flag (P) is set if after any arithmetical or logical operation the number of l's of the result is even.
4. Explain the register transfer instructions along with their timing signals required during the fetch and decode phase of an instruction using the common bus structure. Also derive the logic gates and draw the bus structure required for these RTs.
1) In a computer with 64 bit data bus, 8 number of 8 bit wide memory component is used a True b False 2) When the processor has completed the instruction in M3, where is 9? a) in m2 and the register 2 b) in m1 and the instruction pointer C) only in the accumulator d) in m5 and the accumulator
A memory has 8 megabytes of cells(a) What is the size of its MAR?(b) If 2-dimensional addressing is used, what is the size of each of the horizontaland vertical decoders?
A 1 Kilobyte RAM has a word size of 8 bits. (a) How many address bits does the RAM require? (b) How many D latches does the RAM require? (c) Draw a clearly labeled logic diagram of a binary storage cell and describe. (d) Explain the concept of read and write for a memory unit.
6. In common bus system, all registers are connected to common bus through multiplexers. Design a common bus for eight 6-bit registers (R1, R2, . R8).
Write the microprocessor code that collects (33)16 data with (2F)16 information
3. Draw the complete block diagram for an 8086 Microprocessor system with 8-push button switches and 8-LEDs in detail assuming the input/output (I/O) address is (33H). املة تحمل N
Interfacing: Memory with 8051 O Design a 8051 micro controller with following specification 8051 CPU at 12 MHz * 32kB Program memory (ROM) * 16KB Data memory (RAM)