3. A concrete beam as shown in the figure spans 6m, and supports a permanent CHB wall, floor slab, ceiling & its structural framing, mechanical and electrical systems. Determine the uniform dead load in kN/m acting on the beam. The wall is 3m high and 100mm thick. The floor slab is 125mm thick and spans over simply supported beam with a tributary width of 2.4m. The estimated load for ceiling and its framing is 1.2 kPa. The estimated load for mechanical and electrical systems is 0.4 kPa. Use 24 kN/m^3 for the unit weight of concrete wall load WAレL floor slab FLOOR ceiling, stee frmng, etc. mechanical, BEAM. electrical load CEレレ ТОTAL HANEES. 上に代 Cん Duct

3. A concrete beam as shown in the figure spans 6m, and supports a permanent CHB wall, floor slab, ceiling & its structural framing, mechanical and electrical systems. Determine the uniform dead load in kN/m acting on the beam. The wall is 3m high and 100mm thick. The floor slab is 125mm thick and spans over simply supported beam with a tributary width of 2.4m. The estimated load for ceiling and its framing is 1.2 kPa. The estimated load for mechanical and electrical systems is 0.4 kPa. Use 24 kN/m^3 for the unit weight of concrete wall load WAレL floor slab FLOOR ceiling, stee frmng, etc. mechanical, BEAM. electrical load CEレレ ТОTAL HANEES. 上に代 Cん Duct

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: SITUATION. The cable of a suspension bridge shown in the figure below runs over a tric pulley on the…

A: It is given that :

Q: In the floor plan below, the rigidities of walls A, B, and C are 1.0. The rigidity of wall D is 1.5.…

A: We need to use the diaphragm method to analyze the lateral load resistance of the building. In this…

Q: A concrete framework is used to support a 125 mm reinforced concrete slab that carries a uniform…

A: Load due to slab: The dimension of the slab is 5.5 m×3 m. The thickness of the sab is 0.125 m. The…

Q: An aluminum alloy pipe with an outside diameter of 3.1 in. and a wall thickness of 3/16 in.…

A: It has been asked in the question to determine (a) Compute the maximum value of Q for the pipe. (b)…

Q: A 1.6-m-long cantilever beam supports a concentrated load of P = 7.2 kN. The beam is made of a…

Q: SITUATION. The cable of a suspension bridge shown in the figure below runs over a frictionless…

A: given data w = 160 kN/m permissible working stress= 800 MPa Unit weight of concrete is 23.4 kN/m3.…

Q: A timber beam 150 mm wide by 250 mm deep is to be reinforced at the top and bottom by steel plates…

A: Given : Width of beam = 150 mm Depth of beam = 250 mm Thickness of steel plate = 10 mm Moment = 40…

Q: A timber beam triangular in section of base 100 mm and altitude 200 mm carries the loading as shown.…

A: Support Reactions : Taking moment about B, MB = 0RA×4 - w×4×2 - P×1 = 0RA = 2w + P4∑Fy = 0RA + RB =…

Q: simply supported wood beam AB with span length L = 4 m carries a trapezoidal distributed load (see…

A: Given data in question Loading Span member length Cross section dimensions To find out Bending…

Q: 1. The stairs of a high rise reinforced concrete building consists of a flight of steps cantilever…

A: Given data length of cantilever steps= 1.5 m assume n=15 we have to compute the area of steel r/f…

Q: 3. A concrete framework is used to support a 125 mm reinforced concrete slab that carries a uniform…

A: Given Data, • Size of slab = 5.5 m x 3 m • Thickness of slab = 125 mm = 0.125 m • Concrete density =…

Q: Example 7.8 Design a lintel over an opening of 3.5 m. The lintel is made in a wall 400 mm thick The…

Q: For the thin-walled tubular section shown in the Figures that is applied a moment T = 4 kN * m,…

A: The strength of modern lightweight thin-walled structures is usually limited by the strength of…

Q: r a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live…

A: Given:- t=100mm width=300mm depth=500mm fy=415MPa dead load of 1.77 kPa and service live load of…

Q: A reinforced concrete beam has a width of 300 mm and an overall depth of 510 mm.The beam is simply…

Q: A wood beam supports the loads shown. The cross-sectional dimensions of the beam are shown in the…

Concept explainers

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.

Question

3. A concrete beam as shown in the figure spans 6m, and supports a permanent CHB wall, floor slab,
ceiling & its structural framing, mechanical and electrical systems. Determine the uniform dead load
in kN/m acting on the beam.
The wall is 3m high and 100mm thick. The floor slab is 125mm thick and spans over simply
supported beam with a tributary width of 2.4m. The estimated load for ceiling and its framing is 1.2
kPa. The estimated load for mechanical and electrical systems is 0.4 kPa. Use 24 kN/m^3 for the unit
weight of concrete
wall load
WA LL
floor slab
FLOOR
ceiling, stee
frmng, etc.
mechanical,
BEAM
electrical
load
CEレル
ТОTAL
HANEBES,
上EettANichL
Duct

wall load
WALL
floor slab
FLoOk
ceiling, stee
frmng, etc.
теchanical,
BEAM
electrical
load
CEILIN
ТОTAL
HANEEES,
MECHANIChe
Duct

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

EXAMPLE 7-1 = The beam shown in Fig. 7-10a is made of wood and is subjected to a resultant internal vertical shear force of V 3 kN. (a) Determine the shear stress in the beam at point P, and (b) compute the maximum shear stress in the beam. 50 mm 125 mm V= 3 kN 100 mm 37.5 mm (a)
A (1.6 m) long cantilever beam supports a concentrated load of (7.2 kN), as shown below. The beam is made of a rectangular timber having a width of (120 mm) and *.a depth of (280 mm). Calculate the maximum shear stress in the beam 7.2 kN 280 mm 1.6 m 120 mm 301 kPa 241 kPa 321 kPa 141 kPa
In the floor plan below, the rigidities of walls A, B, and C are 1.0. The rigidity of wall D is 1.5. For a force of 100 kips in the horizontal direction, determine the maximum diaphragm shear per unit depth (absolute value). Assume that the center of mass is at the center of the diaphragm. To obtain this answer you will first need to compute the location of the center of rigidity and the force in each wall. 10' 10' A 10' CR D 10' X B
SITUATION. The cable of a suspension bridge shown in the figure below runs over a frictionless pulley on the top of each of the towers at A and B and is fixed to anchor blocks at D and E. The cable carries a uniform horizontally distributed load of w = 160 kN/m. The permissible working stress of the gross area of the cable, including voids, is 800 MPa. Unit weight of concrete is 23.4 kN/m³. For this problem, L= 400m, S = 40m, H = 60m, a = 45°. L H W(kN/m) F Anchor Zoom image Determine the required volume of the concrete anchor blocks in m³. 2600 2800 3000 2500 Anchor
The floor of a heavy storage warehouse building is made of 150 mm thick stone reinforced concrete. If the floor is a slab having a length of 7m and width of 2.5m, determine the resultant force in KN caused by the dead load and the live load.
A floor is supported by 100 mm x 200 mm wooden joists spaced at 300mm on centers with an effective span of 3m. The total floor load transmitted to the joists is 2.5kPa. If the unit weight of wood is 7 kN/m³ and elastic modulus of wood is 12x103 MPa. (a) Determine the maximum bending stress (fp). (b) Determine the maximum shearing stress (fy). (c) Determine the maximum deflection (8maximum).
subject : Geotechnical DesignBook : PRINCIPLE OF FOUNDATION ENGINEERING
An aluminum alloy pipe with an outside diameter of 4.0 in. and a wall thickness of 6/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 11 lb/ft at its base to wB = 17 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?