3. A compound pendulum shown in Fig. 3 consists of a rod AB with mAB = mcD = 5 kg, and a disk with mp = 5 kg. (1) Determine the center of gravity G. (2) Determine the mass moment of inertia about G, i.e., IG. (3) Determine its mass moment of inertia about O, i.e., Io. 10 kg, a rod CD with

3. A compound pendulum shown in Fig. 3 consists of a rod AB with mAB = mcD = 5 kg, and a disk with mp = 5 kg. (1) Determine the center of gravity G. (2) Determine the mass moment of inertia about G, i.e., IG. (3) Determine its mass moment of inertia about O, i.e., Io. 10 kg, a rod CD with

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flywheel of mass 0.9 ton is fitted to a multi cylinder engine, which runs at a mean speed of 380 r.p.m. If the speed varies from 9 % above the mean to 6 % below it and the fluctuation energy is 1100 kN-cm, find (i) mass moment of inertia of the wheel and (ii) radius of Gyration.
Hello! I need help with this question :<
1. A circular disk has a density p(r) which varies as a function of distance from the center of the disk. The disk has a radius R and a thickness t. Assuming p(r) = Po(1-r/R): Calculate the total mass of the disk. a. b. Calculate the moment of inertia of the disk about an axis out of the plane of the page and passing through Point G. C. Calculate the moment of inertia of the disk about an axis out of the plane of the page and passing through Point O. G R
The spring, Parts of a Vehicle weigh (9.79KN), sta center of gran'ty is (106.7cm) behind the front axle & wheelbam is (223.6cm) - The combined Stiffness of the Springs ot the front suspension is ( 24.52 kN/m) & that of the rear suspinsion is (26.27KN/m). The radius of ayration of the spruny a horizontal transverse axis through the center ot gravity is (102.6cm) .Calculate 'the natural freguemcies of the pitch & bounce motions of the vehicle Also de termine the locations ol osc;llatn bodg. parts about enters.
An elliptical hoop of negligible thickness with a vertical orientated semi-major axis a and a horizontal orientated semi-minor axis b, which has a mass per unit length of p, is mounted on a circular peg to which is attached a Carte- sian xy coordinate system in a vertical orienta- tion as shown in the accompanying sketch (the gravity g ellipse and peg are not rigidly joined to each other and are simply in kinematic contact with each other with negligible friction), such that the physical system lies within a flat ry plane. The ellipse is then allowed to freely oscillate in a to-and-fro rocking motion by a small angle 0, such that the gravitational acceleration g acts in a downwards direction that is parallel to the ellipse semi-major axis. 1.3 a 1.4 b Considering the above system determine the following information clearly showing all steps and appropriate reasoning: Y Utilizing the previously derived equation of motion determine the corresponding natural angular frequency wn for the…
2. A disc 30 cm diameter and 4 cm thick and density 0.0078 kg/cm³ oscillates at a frequency of 5 Hz on one end of a shaft which is built-in at the other end. When an unknown disc is added to the first disc, the frequency is reduced to 3.4 Hz. Find the moment of inertia of the unknown disc. 0.289 kg m² Ans.
Moment of inertia of a square about its centroidal axis decreases with decrease in side of the square. Justify this statement with your own example.
Obtain the moment of inertia () of the flywheel from its dimensions (see figure below). Note that the flywheel is two cylinders of diameter 0.03086 m and one cylinder of diameter 0.2008 m. (For uniform cylinders, /= 1/2(MR2)) Since the masses are unknown, express the mass as the density (p) times the volume. Each part of the flywheel is made of the same material so there is only one density. You should now have an expression for the density in terms of I, the two diameters, the two thicknesses, and constants. 0.0520 m 0.03086 m 0.2008 m 0.0155 m
dsphere dbar • Given the above system, two spheres attached to the ends of a cylinder, determine the mass moment of inertia about the axis normal to the page as a function of the variables provided. Note, you can treat the masses of each element of the system as known o (msphere and mbar). After deriving an expression for the mass moment of inertia about the axis normal to the page as a function of the variables, calculate the mass moment of inertia given: osphere properties ▪ mass of sphere = 5 kg 1 diameter of sphere = 0.5 m bar properties ▪ • Determine the resultant force and moment acting on the system if the system is moving as follows: mass of bar = 25 kg length of bar = 7.5 m diameter of bar = 0.25 m O a = 5î+ 2ĵ m/s² O αG = 7k rad/s² ασ
Rotattional Inertia of a two-particle system a-) What is the rotational inertia ( lcom) about an axis throgh the center of mass perpendicular to the rod as shown in figure (a)? b-) What is the rotational inertia of the body about an axis through the left end of the rod and parallel to the first axis as shown in figure (b)?