3. A 5m long x Im wide horizontal plate is heated on top and insulated on the bottom. The plate is maintained at 100°C. The air and walls of the room are maintained at 25°C. Determine the heat transfer by nature convection and radiation heat transfer. Also discuss the effect of a 5 m/s flow of air passing parallel along the 5m length of the plate. Should natural convection be considered with the 5m/s flow?

3. A 5m long x Im wide horizontal plate is heated on top and insulated on the bottom. The plate is maintained at 100°C. The air and walls of the room are maintained at 25°C. Determine the heat transfer by nature convection and radiation heat transfer. Also discuss the effect of a 5 m/s flow of air passing parallel along the 5m length of the plate. Should natural convection be considered with the 5m/s flow?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.40P

See similar textbooks

Similar questions

Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
A sphere of 74 mm diameter is moving through the air at a velocity of 0.035 m/s. The surface temperatureof the sphere is uniform at 40◦C and the air temperature is 20◦C. What is the average convection coefficientbetween the sphere and air
Can anyone help me with this Heat Transfer question
Need answer ASAP! Thank you Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 10 W/(m2-K). Assume the apple can be described as a sphere with an 8 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.4 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3 a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?
only first attempt
ricant An oil is acting as a lubricant for a pair of cylindrical surfaces such as those shown in 1. The angular velocity of the outer cylinder is 7908 rpmt. The outer cylinder has a radius of 5.06 cm, and the clearance between the cylinders is 0.027 cm. What is the maxi- mum temperature in the oil if both wall temperatures are known to be 158° F? The physical properties of the oil are viscosity density thermal conductivity 92.3 cp 1.22 g cm-3 0.0055 cal sec-1 cm-1 ° C-1
A food product with 80% moisture content in a 5 cm diameter can wants to be frozen. The density of the product is 1000 kg / m cubic, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -1.75 ° C. After 10 hours in -25 ° C freezing medium, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder
H.W. Q1: Consider a hot automotive engine, which can be approximated as 0.40m wide, and 0.8m long rectangular block. The bottom surface of the block is at a temperature of 80°C and has an emissivity of 0.95. The ambient air is at 20°C, and the road surface is at 25°C. Determine the rate of heat transfer from the bottom surface of the engine block by convection and radiation as the car travels at a velocity of 80 km/h. Assume, the flow to be turbulent over the entire surface because of the constant agitation of the engine block. k = 0.02735 W/m.°C v=1.798×10* m²/s Air properties at Tf= 50 °C: Pr = 0.7228 Answer: Qcony = 1363 W, Qrad = 132 W, Qotal = 1495 w Hint: Use the correlations (equations) of average Reynold number (ReL). L = 0.8 m Engine block Air V, = 80 km/h T. = 20°C T; = 80°C ɛ = 0.95
Write the comparison between forced and free convection in a non-isothermal system?
Air at 27 ⁰C and 1 atm flows over a flat plate at a velocity of 3m/s, assuming the plate is heated its entire length to a temperature of 70⁰C. Heat transferred in first 25 cm of the plate is?
A hot plate 1.2 m wide, 0.35 m high and at 115 0C is exposed to the ambient still air at25 0C. Calculate the following: (i). Average heat transfer coefﬁcient over the surface ofthe plate; (ii) Heat loss from the plate; (iii) Rise in temperature of the air passing throughthe boundary. Properties of air at 70 C temperature are: r = 1.029 Kg/m3; Cp = 1005 J/KgK; K = 0.0267 W/m K; m = 1.866 * 10'5 N- S/mz; Ans: Gr = 27.532*107 (i) h = 5.43 W/m2C; (ii) Q = 410.5W (iii) At = 85.45 C