3. A 3" diameter pneumatic piston is used to lift a load of 100 lb. A. What air pressure is required to accomplish this task? B. What volume of air at this pressure is required to extend the piston 10"? C What

Q: A gear reduction system consists of two gears: E and X. Gear E rotates clockwise with a constant…

A: Given data: αE=4.5 rad/s2ωE=7 rad/s Need to determine select the correct statement.

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: find the center of the given shape

A:

Q: The triple thread screw has a lead of 15 mm. Determine its thread per inch.

A: Given               Lead, L = 15 mm                           = 0.59 in No of thread, n = 3 Find…

Q: in a planetary gear train, the arm C caries two gears A and B and a compound gear D-E. The gear A…

A:

Q: 5. Determine the radius of gyration.

A:

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A: Given Shaded area To find Centroid

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to calculate third view

Q: 20.0 60.0 The three displacement vectors in the drawing have magnitudes of A-4.61 m, B-5.22 m, and…

A:

Q: w the components of F along the u and v w the triangle with sides and angles labeled to be able to…

A:

Q: It is known that the connecting rod AB exerts on the crank BC a 2.5-kN force directed down and to…

A: The free-body diagram of the given system is shown below.

Q: If P =600 lb, determine the angle alpha so that the resultant of the system is purely vertical.…

A:

Q: Two parallel shafts A and B, 36 in. apart, are connected by a belt drive. The driving pulley rotates…

A:

Q: 6. FA and FB balances the metal beam with a 360N of weight. FB experiences a force of 200N while Fa…

A: According to the given information, we have two reaction forces FA and  FB  where the weight on the…

Q: Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly…

A: Given data wA = 1500rpm wB= 500rpm  TA= 20

Q: solve using analytical way Given a single disk system that rotates as in picture. If: m₁ = 10 kg; R₁…

A: co-ordinates are converted into x-y form. center of mass is found in x-y form and from there…

Q: 1-23.Determine the length of side C of the triangle shown in Figure P1-23.

A:

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: The lower half of the moulding box is O a. Raiser O b. Drag O . Runner O d. cope

A: Given data Lower half of the moulding box is

Q: K.

A: For solution refer below image.

Q: Determine the angle made between the axes OA and AC.

A: The position vector of the point O with respect to point A is The position vector of the point C…

Q: Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of…

A:

Q: Parallelogram The accompanying figure shows parallelogram ABCD and the midpoint P of diagonal BD. a.…

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: A 250 mm. 3 B 4 150 mm. C D 112.5 mm.

A:

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: Find the shortest distance from point B to line AC

A: Position vector for OB is OB=7j-3k Position vector for OC is OC=7j+5k Position vector for OA is…

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: Determine the distance of the center of mass of the bracket shown measured from the base. Use three…

A:

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to find three views.

Q: 1 mm 10 mm 1 mm Y axis 5 mm 10 mm 1 mm X-axis

A:

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: What is the direction of the edge formed between the intersection of (211) and (102)?

A:

Q: Given the Isometric views, draw the three orthographic views below

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 unit.

Q: The power and motion can be transmitted from one shaft to another shaft by means of gear drives

A: According to given details provided in the question

Q: The two gears in the picture below on the left are meshing together. The two gears in the picture on…

A: A-The two meshing gears have the same module. When two gear meshes, the module (which is defined as…

Q: O Aveclar Af Length 10 units makes an angle. of 30 with avectorBofenoth 6units. Find the…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.