3- The single phase loads in the circuit can be described as follows: Load_1 absorbs an average power of 8-kW at a leading power factor of 0.8, Load_2 absorbs 20-kVA lagging power factor of 0.6, Load_3 absorbs 12-kVAr lagging power factor of 0.85. a) Determine the power factor of the three loads in parallel. b) Determine the apparent power required to supply the loads, the magnitude of the current, Is, and the average power loss in the transmission line. c) Determine the amplitude of source voltage Vs. 0.052 jo.502 12 Is Vs 250LO'Vms L1 L2 L3

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: Can you please picture the solution again? because it's too vague, I can't read very well. Thank…

A: It is asked to picture the provided solution again.

Q: A point at which two or more elements have a common connection is called Select one: a. A contact…

A: Given :   In the question they have mentioned a statement and they want to know the the meaning of…

Q: Which is a better source of information, the power supply or the DMM? Why?

A:

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: What is sourcing current, and its connection to switching of power? It's confusing. Please help.

A: Power: It is amount of energy which transferred per unit time, it means rate of doing work. It is a…

Q: What are the key challenges in power transmission within a power grid?

A: Key challenges in power transmission within a power grid?

Q: Hi,  Are you able to go into some more detail on its opperation if possible.

A: Given: To explain: The operation of the circuit as a NOT gate.

Q: Coriolis flow meter is a type of -------- flow meter.

A:

Q: * Q) DC bridge are used for measurement of capacitance. O measurement of current. O measurement of…

A: DC bridges

Q: what was the calculation done to get d? Confused on how this was rearranged.

A:

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: Can you help me with questions two and three please?

A: Present StateNext State (UP)Next State…

Q: A dwelling has a 200-ampere service that is fed with THHW copper conductors. What is the minimum…

A: A dwelling has a 200-ampere service that is fed with THHW copper conductors.

Q: 4. Bus bars are either flat tubes as these shapes allow heat to or dissipate more efficiently.

A: The size of bus bar determines the amount of current flows through it safely. The heat dissipation…

Q: Please answer in typing format

A: The Peltier effect is the result when electric current is passed between two materials,such that it…

Q: What are the basic/necessary steps to design a pico hydro power plant? Inlcude the parts of…

A: The basic/necessary steps to design a pico hydropower plant: • It should be practical and suitable,…

Q: Electric Powers System for Nonelectrical Professional can you describe effective preventive…

A: Electrical Preventive Maintenance (EPM) is the act of leading routine assessments, tests, and the…

Q: Fill in the blanks for Ampacity, Voltage, Power and Resistance

A:

Q: What is the area of ​​the shaded part

A:

Q: L{7te¬5t cosh(3t) + +sin(Võt) – rº + e%}

A:

Q: where is the value of 10/sqrt(2) coming from?

A:

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: Reactances are connected in series: |Xc11 = 100, IXC2| = 40, |X_11 = 30, XL21 = 70. What is the net…

A: To find net reactance

Q: in this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1)  Legally Required standby systems provide electric power to selected loads during firefighting…

Q: In oil emerged kva is there any piping and instrumentation diagram provided by the manufacturer. Can…

A: In the context of an oil-immersed KVA (kilovolt-ampere) transformer, the presence of a piping and…

Q: How to convert 22 mW of power into the units of dBm

A: In this case, 22 mW of power is to be converted into its equivalent power in dBm.

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: 1) Given the figure and values below: R = 5.6 kfl , Rc = 4.7 kil , Rg = 1.2 kfl, Vcc = 18 V, Vc = 12…

A:

Q: What is EMMI?

A: EMMI tends for ELECTRICAL MEASUREMENT AND MEASURING INSTRUMENTS.

Q: explain the Reasons for coordinating electrical protections

A:

Q: Identify a specific place where you can possibly install a micro-hydro power  plant. Discuss why?

A: The explanation is as follows.

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.