3 - The material of the beam given below is C35/45 – B420C and it is good quality concrete. The concrete cover is given as 50 mm The span moment (Md) of the beam is 526 kNm The dimensions of the bearn are given as b:820 mm, bw:350 mm, t:130 mm, h: 700 mm. Then determine the minimum number of steel rebars to be placed on the span region of beam by using $28. b h-t bw

3 - The material of the beam given below is C35/45 – B420C and it is good quality concrete. The concrete cover is given as 50 mm The span moment (Md) of the beam is 526 kNm The dimensions of the bearn are given as b:820 mm, bw:350 mm, t:130 mm, h: 700 mm. Then determine the minimum number of steel rebars to be placed on the span region of beam by using $28. b h-t bw

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Number 1 (parts i, ii, iii) please :)
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
Answer Options Correct Q.No Question/Statement Answer A Select the grade of concrete required for 1 М5 M50 M15 М80 airport runways. The load which has fixed size and location is 2 called as Environmental All answers Dead load Live load Load are wrong Top surface of the tensile Bottom The clear cover of the RCC beam is taken as Centre of surface of the Bottom of the gravity of the tensile steel vertical distance from the base of the beam to steel tensile steel beam the reinforcement reinforcement 4 Stocky column generally fails by_ Compression Tension Buckling Deflection In a one way slab the main reinforcement is provided along All answers Both long and short span Long span Short span are wrong All answers Flat slab is placed above Drop panels Column Column head are correct The maximum percentage of reinforcement in 7 RCC short column, based on practical 0.8% 4% 6% 2% difficulties is For reinforced concrete wall D4B When to columns are far, select the type of foundation Trapezoidal…
As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B 30'-0"- B2 -EQ.- EQ. -EQ. SEC 1 -40'-0" IS B1 B3 B3 B1 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in². EQ. 40'-0" B EQ. North
need answer thank you
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
Principle of Reinforced Concrete Design
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
A circular Column has dia of D 30 in. Concrete Compressive strength at 28 days is of steel is (60 + 60) ksi. Determine the design capacity of circular column and 8 # 11 bars is used. (4 + 60) ksi and yielding strength
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
Size an A992 W shape given the following information; -Beam span is 20 ft and simply supported -Floor beams are 6 ft on center -Cb=1.0 (don't forget self-weight) -The beam will support a plywood deck (3 PSF) oriented perpendicular to the beam -The average concrete (normal weight) thickness is 4.5 in Assumption - 50% ponding factor during the concrete placement and treat the concrete as a live load - 10 Psf for the concrete workers live load - Plywood framework is used instead of steel decking - the beam has no support of the compression flange over its length