3- The 8086 to enable the mostsignificant data bus bits (D15-D8) during a read or a writeoperation using------O A- RD, WR pinО в ВНЕВ-ВНЕ pinO C-S3/S6 status bus pinO D- 10/ M 4- A basic computer has 12registers, a memory unit and acontrol unit. The number of itscommon bus selectors is:O A-3О В4О с5O D-6

Bus High Enable/Status. During T1 it is low. It is used to enable data onto the most significant…

Answered: 3- The 8086 to enable the most…

3- The 8086 to enable the most significant data bus bits (D15- D8) during a read or a write operation using------- O A- RD, WR pin O B- BHE pin O C- S3/S6 status bus pin O D- 10/ M

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A reset input is used in IC 7493, why? a. For reset the counter b. For setting the counter c. For decrement of bit by 1 d. For increment of bit by 1
B. Determine the amount of time delay operation of 12-bit serial in / serial out shift register Data in SRG 12-bit Q11 data out CLK F=100 KH
3. The timing diagram below is for the 8-bit register block shown. Complete the timing diagram by filling in the output (q) signal. load q(N-1.0)+ cik cir Input(N-1.0) cik Register cir load input 45 A3 4B FF 44 01 02 CA 66 7A 98 9
Instruction MOV [SI+0007], AX .is ......... addressing mode indexed O non of those direct register indirect O The instruction JNE is equal to JZ O JNG O non of all O JNL O JNZ !
i l. I. A V:-9 How many parallel signal lines that * ?control bus consist of 4-9 4-11 4-10 4-12 :The first 16-bit microprocessor refers to 8088 8086 8085 8084 In Address Bus, If the CPU has N address lines then it can directly address .memory locations 3*N O 2+N 2N II
Interface an input port 74LS245 to read the status of switches SW1 to SW8. The switches when shorted input a ‘1’ else input a ‘0’ to the microprocessors system. Store the statusi inregister BL. The address of the port is 0740H.
Answer the question of the Microprocessor and Microcontroller.
DIGIT ELECTRONICS
Importance of pin PULL-UP in any microcontroller is O A. to save the power supply O B. to supply voltage to the pin O C. to protect the logic input from noise O D. to understand the logic input high
An LD instruction, located at x4008, loads register R4 with the content of a memory location. What is the lowest address that can be read? O X3F08 O X4F09 O X4F0B O X3F09 O x4109
What is the total capacity in hexadecimal representation for any segment base address wtihin the 8086 microprocessor's real address mode RAM?-FEFFh-BHAFh-FFFFh-EEEEh
a) The 74ALS174 is normally used for synchronous parallel data transfer whereby the logic levels present at the D inputs are transferred to the corresponding Q outputs when a Positive Going Transition (PGT) occurs at the clock, CP. However, this IC can be wired for a serial data transfer as shown in Figure 1. Serial data will enter at D5 and will output at Qo. A signal as shown in APPENDIX 1 is applied to the shift register in Figure 1: (i) Determine the resultant output waveform (ii) How many clock pulses is needed to completely load the entire signal? Serial Input D5 D4 D3 D2 D, Do CP- 74ALS174 MR- Qs Q. Q3 Q2 Q, Qo Serial output Figure 1