Q3/A- Write a program to find Largest No. in a block of data. Length of block is OA. Store the maximum inlocation result.B- show how to implement 64KX 16 EPROM using two 32KX8 EPROM?C- List the pins related to the interrupts, At what address are CSao and IPA0 stored in memory?D- If an 8086 running at 8 MHz performs bus cycles with six wait states, what is the duration of the bus cycle?

Assembly program to find Largest no in block of data is 0A and we have to store the maximum in…

3/ A- Write a program to find Largest No. in a block of data. Length of block is OA. Store the maximum in location result. B- show how to implement 64KX 16 EPROM using two 32K×8 EPROM? C- List the pins related to the interrupts, At what address are CSao and IPao stored in memory? D- If an 8086 running at 8 MHz performs bus cycles with six wait states, what is the duration of the bus cycle?

3/ A- Write a program to find Largest No. in a block of data. Length of block is OA. Store the maximum in location result. B- show how to implement 64KX 16 EPROM using two 32K×8 EPROM? C- List the pins related to the interrupts, At what address are CSao and IPao stored in memory? D- If an 8086 running at 8 MHz performs bus cycles with six wait states, what is the duration of the bus cycle?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

The answer is provided. I need detailed steps and explanation of the solution please. 14. What address in the Interrupt Vector Table is used to contain the address of the ISR for Interrupt #0A ? Please give answer in hex. 28 - 4*10 = 40 = 32+8
Homework: Show how a 32Kbyte ROM module can be connected on an 8088 system using 2764 EPROM chips, occupying the address range starting from the address E0000H. Use the following address decoding circuits: Nand decoding circuits A line decoder and a Nand gate PLD decoding circuit Comparators only Line decoder and a comparator 1 Solution: A19 A18 A17 A16 A15 A14 A13 A12 A1... A. Memory Map Size of 2764 EPROM chips: Number of chips needed: Number of address lines: 66 2345
Write a procedure, called ADD.BCD, that will add two 8-bit packed BCD numbers and store the result in memory location 30H. Assume the original numbers are stored in R1 and R2 before calling the procedure. Your program should NOT use the "DA" (decimal adjust) instruction. For example, assume R1 and R2 have values 29H and 27H, the result should be 56H. Assume that the resulting BCD number can be correctly represented in a single byte (i.e. 2 BCD digits only). Below is the exact operation of the DA instruction for your reference. Use conditional jumps IF (A3-09) OR (AC = 1) A = A +6 IF (A749) OR (C = 1) A = A + 60h
PC is added to 4 in the given datapath. Why? Your answer: a-To find the relative branching address b-To find the absolute branching address c-To find the address of the next instruction d-To execute add instruction
The FIQ interrupt techniques are required to hook and chain at the offset of the Interrupt Vector Table. It.?
Change this MIPS code to RISC-V Assembly using store-load and 2 memory locations. Please add comments. Allow running in RARS.
3. Write an 8086 program to count up from 00 to 60 in precise time delay intervals. The delay is to be carried out in a subroutine and the delay time parameter is to be passed to it in register BL.
IN x86 assembly, Provide a scrrenshot of the codes result
Q:Answer the following sentence with (True) or (False) and correct the false answer: 1. You can input data of size 16-bit through the fixed port. 2. In the maximum mode, the status signals S₁, S₂ and S3 are controlled by the bus controller. 3. HLDA is an output signal. 4. In 8086, when executing the instruction MOV AL, [SI+100D H] where SI-100AH, Ao=0 and BHE=1 5. When S, is 0, the TF is disabled.
I asked the question before and the answer I got does not makes sense. My question is why did not we considered the Adder, Shift, ANd, Control when calculation delay time.? Again, it is in Risc-V.
y of H Q. For the given circuit, which of the following is correct? E OF RAM 256 X 4 A. The number 5 is being written to the memory at address location 203. B. The chip has not been enabled, since the EN terminal is 0; therefore, nothing will be written to the chip and the output is tri- 1 A0 1 A1 O A2 O A3 1 A4 A 255 O A5 1 A6 1 A7 71 QO stated. O DO 1 D1 O D2 1 D3 C. Decimal 10 is being written into memory location 211. D. The read/write line is LOW; therefore, WRITE decimal 5 is being stored at memory O R/W O CS READ EN location 211. Data inputs Address inputs DDDD Data outputs
None