3 - A roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm-diameter rivets are required to fasten member BC to the gusset plate? Member BE? P = 200 kN 6 m 14 mm gusset plate 4 m 4 m E 4 m 4 m PeE P/2 P P/2 75 x 75 x 13 mm 75 x 75 x 6 mm Pac B.

3 - A roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm-diameter rivets are required to fasten member BC to the gusset plate? Member BE? P = 200 kN 6 m 14 mm gusset plate 4 m 4 m E 4 m 4 m PeE P/2 P P/2 75 x 75 x 13 mm 75 x 75 x 6 mm Pac B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the smallest allowable cross-sectional areas of members BD, BE, and DE of the truss shown. The working stresses are 20000 psi in tension and 12000 psi in compression. (A reduced stress in compression is specified to reduce the danger of buckling.)
The steel tie bar shown is to be designed to carry a tension force of magnitudeP=120 kN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel tobe used, the maximum allowable stresses are σ =175 MPa, τ =100 MPa,and σb=350 MPa. Design the tie bar by determining the required values of(a) the diameter d of the bolt, (b) the dimension b at each end of the bar, and(c) the dimension h of the bar.
Question 2 The rods BE and CD are made from steel (E=200 GPa), and each have a diameter, P. The ends of the rods are threaded with a pitch, p. The nuts at B and C are initially finger tightened such that they barely touch rigid member ABC. If the nut at C is then tightened by one full turn, determine: (a) the tension in rods BE and CD (b) the distance, uc, that point C on the rigid member ABC moves. Assume a=300 mm, b= 100 mm, c= 2.5 m, d= 6 m, 0=40 mm, and p=1 mm. OA a В E b D C d
A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kNincluding its self-weight which is distributed equally: a.Determine the stress on the lower washers before the buts are tightened. b.Determine the stress int the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. c.Determine the stress int the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt.
The short cylindrical block of aluminum, having an original diameter, do, of 0.4 in. and an original length, Lo, of 2.0 in., is placed in the smooth jaws of a vice and squeezed until the axial load applied is 900 lb. Determine: (a) the decrease in its length (b) its new diameter EAL = 10000ksi and vAL = 0.33 Lo do
Using the analytical method of joints, determine the stress in the members of the truss shown. B Ph=100 N A 4 m Py = 250 N 4 m 3 m
5. Three wood boards, each 3.5 in. wide, are joined by the 3/4-in.-diameter bolt. If the working stresses for wood are 750 psi in tension and 1450 psi in bearing, find the largest allowable value of the force P. ² 1 in. P 2 in. P 1 in. T in.