さン。3- A distance was measured by a steel tape weighing 0.75 kg anda nomiñal length of 30 meters with only two ends and under a44 N tension, it was found to be 216.325 meters..After themeasurement, it was found that the actual length of the tapeっ bのシしみしwhen it is anchored on the ground and under the 44-Newtontension is 30. 002 meters, Find the real value of thedistance?meaşured

Given data, True length of tape = 30 m Incorrect tape length = 30.002 Incorrect measured distance…

3- A distance was measured by a steel a nominal length of 30 meterş with only two ends and under a 44 N tension, it was found to be 216.325 meters.After the measurement, it when it is anchored on the ground and under the 44-Newton tension is 30. 002 meters, Find the real value of the distance? tape weighing 0.75 kg and のしみ was found that the actual length of the tape レん meaşured

3- A distance was measured by a steel a nominal length of 30 meterş with only two ends and under a 44 N tension, it was found to be 216.325 meters.After the measurement, it when it is anchored on the ground and under the 44-Newton tension is 30. 002 meters, Find the real value of the distance? tape weighing 0.75 kg and のしみ was found that the actual length of the tape レん meaşured

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude of the resultant force acting on the plate as shown: USE THE VALUE OF SET B
A steel rod of length 300 mm and diameter 30 mm, is subjected to a pull 'P' while the temperáture Is 100°C. If the total extension of the rod is 0.40 mm, calculate the magnitude of 'P'. Take 'a' for steel 12 x 10 °C and E = 0.215 x 1012 N/m2. %3D
The rectangular plate (L,xL,) given below is installed between two rigid walls and is deformed as shown by dashed lines. Determine the shear strain y and Yxy at point A. Use the table given below and your student ID to find the values of L, L, a, and b. L2 A b. L. b L, (mm) (mm) (mm) 150 200.0 3.0 3.0
The example of magnetic ciruit of machine parts is a.commutator b.Brushes c.Armature windings d.Field poles
Q2. What is the minixim vahe of thickness that can used. Use the inforamtion proviled in the table bekw. (30 Mark) P.(MPa) 6, (MPa) T, (MPa) D (m) SL (mm) S (mm) (mm) (mm) 1.3 14 12 60 30 1.4 90 16
EM6
D Question 7 A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and has an elongation of 0.009 in. The initial radius of the material is most nearly? O 0.94 in O 0.10 in O 0.31 in O 2.83 in
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
mm l L-1000 A tape 30 m long, 0.6 cm wide and 0.5 mm thick was used to measure a distance of 1000 m at a temperature of 20°C with 120N tension force, mass of tape is 0.7 kg, determine coefficient of thermal expansion of a tape, if: Po Standard tension 50N Modulus of elasticity (E) = 210 kN/mm² 210x6² Standard temperature 35 °C TS Correct measured distance = 999.75 m (1000-999.75)=(P-PO) XL AE W²L гург 0125=(120-50) x 30x1² (0.006 x00005) X2-
A beam with the cross-section given below is subjected to a positive bending moment (causing compression at the top) of 16 kN-m acting around the horizontal axis. The tensile force acting on the hatched area of the cross-section is 75 934001 25 T sol vaill 50 gs bunt ↓ 008 al 150- 100-