3: A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m³/hr.raw water and the detention time is 2 hrs. Find: 1) Radius and depth of the tank 2) Weir loading inm³/m.d. 3) Diameter of the smallest settling particle is to be removed, if v, 1.2 m/hr, p=2 g/cc,P1 g/cc, and μ-1.3 c.p.4: Find the following:1) The settling velocity in water at 20 °C of spherical particle of 4.5 103 cm in diameter and aspecific gravity of 2.65 (viscosity at 20 °C is 1.009 *102 Poise).2) The rising velocity of the particle in 1, if its specific gravity is 0.8.3) The settling velocity at 20 °C of spherical particle of 0.12 cm in diameter.

3. Given: Q = 75 m3/hr detention time, t = 2 hrs Vs = 1.2 m/hr μ=1.3 c.p Central chamber = 4 m

3: A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m³/hr. raw water and the detention time is 2 hrs. Find: 1) Radius and depth of the tank m³/m.d. 3) Diameter of the smallest settling particle is to be removed, if v, P1 g/cc, and u-1.3 c.p. 2) Weir loading in 1.2 m/hr, p, 2 g/cc,

3: A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m³/hr. raw water and the detention time is 2 hrs. Find: 1) Radius and depth of the tank m³/m.d. 3) Diameter of the smallest settling particle is to be removed, if v, P1 g/cc, and u-1.3 c.p. 2) Weir loading in 1.2 m/hr, p, 2 g/cc,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A sheet pile has an embedment depth of 12 m in a homogeneous soil stratum. The coefficient of…

Q: For a grit chamber, if the recommended velocity of flow is 0.2 m/s and the detention time is 2…

A: Grit chambers are long broad tanks that are designed to slow down the flow so that solids such as…

Q: Q3) Determine the depth and width at average and minimum flow and dimensions the weir plate of…

Q: The coefficient of permeability of soil around a sheet pile is 10-5 m/s. The flow net of this sheet…

A: Given: The coefficient of permeability is 10-6 m/sec. The number of flow lines is 6. The number of…

Q: A V-notch-shaped bed of trough with a 30" diameter receives backwashing water from a filter layer…

Q: Problem 9.4: An 20 mm of average particle diameter. Taking, n-0.02, So-0.0015, z=2, and will be…

A: An unlined trapezoidal channel Manning's constant, n=0.02 Slope of channel bed, So=0.0015 Side slope…

Q: Problem 3.134. Given: اده Solution: 3L- EL d = ? P = 0.75 SG=1.0 SG=1.2 Pater Find: To what depth d…

A: Given Density of body = 0.75 × density of waterWidth 6 LSpecific gravity = 1 and 1.2 To find out…

Q: Estimate the lea<hing requirement when electrical <onductivity (EC) valve of a saturated extract of…

Q: A municipal wastewater treatment plant with average flow of 1.5 MGD and maximum flow during the day…

A: given average flow = 1.5 MGD peak factor = 2.6

Q: prove only one of the following: Flow plain area 1) SOR=. 2) Newton's law in sedimentation process…

Q: A flownet for flow around a single row of sheet piles in a permeable soil layer is shown in Figure 1…

A: Given,hydraulic conductivity,k=5×10-3cm/s

Q: The hydraulic retention time in the primary sedimentation tank is: Select one: а. 1-2 h b. depends…

A: Hydraulic retention time (HRT) is a measure of the average amount time of time that the…

Q: How can I calculate the water level in a grit chamber at average flow and at peak hourly flow. The…

A: Average daily flow rate, Width of tank, Length, Depth, Elevation, To find: Water level in a grit…

Q: A pipe culvert 45 ft long extends between two reservoirs as shown below. The difference in the water…

Q: treatm plant has seven (one iš standby reating öf water. ach clarifier is 5 m width, 25 m length,…

A: given data discharge for one clariferQ=15m3/min/7Q=2.14m3/mingiven B=5m L=25m d=5m detrntion time…

Q: Anirrigation canal has been designed to have R = 2,5 m and S = 1.6 x 10. The sediment on the bed has…

Q: Determine the surface area of a primary settling tank (expressed in m2) sized to handle a maximum…

A: Calculate the surface area of the tank. Here, Q is the maximum hourly flow, and is the overflow…

Q: Two rectangular settling tanks are each 8m wide 26m long and 2.5 deep. EACH is used alternatively to…

A: Given: The width of the tank is 8 m. The length of the tank is 26 m. The depth of the tank is 2.5 m.…

Q: Assuming the start up flow for the clarifier is 1.7 mgd and the design peak hour flow is 5.2 mgd,…

A: Step 1: Step 2:Step 3:

Q: Q3) Two rectangular clarifiers, each 30 ft long, 15 ft wide, settle 0.40 MGD following alum…

Q: Find the Diameter of the runoff pipe 2 for the following area. A1=1.55*10 km? A2=1.40 102 km?…

Q: (i) Calculate and evaluate the detention time loading in compliance with standard practice given…

Q: please draw normal, shear , and bending moment diagram for this (reactions are already calculated in…

A: The given diagram is shown below, To determine Draw the Shear force and bending moment diagram

Q: A town has an existing horizontal sedimentation flow tank with an overflow rate of 17 m³/day/m², and…

Q: A rectangular clarifier of 30 m length, 10 m width and 4 m depth is provided with a detention time…

Q: A well of 0.1 m radius is part of a wellpoint network to keep an excavation dry. The groundwater at…

Q: A town has an existing horizontal flow sedimentation tank with an overflow rate of 17 m³/day/m², and…

A: Given data- Overflow rate- OFR=17 m3/day/m2, Settling velocity- Vs=0.1 mm/s, Ideal sedimentation…

Q: 6) A rectangular settling basin with dimension (LXWXH) 50m x 25 m x 5 m used to settle particles in…

A: Given L = 50 m W = 25 m H = 5 m Detention time of 2.5 hours

Q: An ideal settling basin is designed with surface overflow rate (SOR) of 1 m³/m²/h. Particles have…

A: Given data- An ideal settling basin- Surface overflow rate- SOR = 1 m3/m2/h, To Find- The value of…

Q: In a wastewater treatment plant, primary sedimentation tank (PST) designed at an overflow rate of 30…

Q: (a) The Top Glove Sdn Bhd has an existing horizontal-flow sedimentation tank with an overflow rate…

A: as per our guidelines i am solving problem "a" only

Q: 5. A radial flow circular sedimentation tank 22 m diameter treating 10,000 m%d of water has an…

Q: )A rectangular grit chamber is designed to remove particles with a diameter of 0.2 mm, specific…

Concept explainers

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.

Question

3: A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m³/hr.
raw water and the detention time is 2 hrs. Find: 1) Radius and depth of the tank 2) Weir loading in
m³/m.d. 3) Diameter of the smallest settling particle is to be removed, if v, 1.2 m/hr, p=2 g/cc,
P1 g/cc, and μ-1.3 c.p.
4: Find the following:
1) The settling velocity in water at 20 °C of spherical particle of 4.5 103 cm in diameter and a
specific gravity of 2.65 (viscosity at 20 °C is 1.009 *102 Poise).
2) The rising velocity of the particle in 1, if its specific gravity is 0.8.
3) The settling velocity at 20 °C of spherical particle of 0.12 cm in diameter.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Measuring sitework, excavation and piling

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the question, thanx.
Sed. Tank
How can I calculate the water level in a grit chamber at average flow and at peak hourly flow. The effluent from the tank flows over a fiberglass, sharp-crested weir that is set at elevation 136.00 ft above sea level (ASL). The average daily flow rate is 2.6 MGD. Assume that all flow must pass through one grit chamber. The dimensions of the grit chamber are 9 ft wide, 30 ft long, and 10.5 ft deep (water depth). The weir extends across the full width of the chamber. Peak hourly flow rate = _____MGD
3
Estimate the removal efficiencies for particles of 0.030mm and 0.015mm, respectively, in the sedimentation tank with an overflow of 2m/m²-h. Discrete settling is assumed for the particles. Furthermore, Stokes' law is assumed to be valid in the determination of the settling velocity (to simplify the calculation). It is known the specific gravity of the particle is 2.65. The gravity accelerate rate is 9.8m/s and the water kinematic viscosity is 1×10m?/s. [Stokes' law v = d²(s=1)º1 18y If the weight fractions of the 0.030mm and 0.015mm particles in the waster are 30% and 70%, respectively, calculate the total removal efficiency (TRE) of these particles by this tank.
A circular sedimentation tank with central chamber of 4 m in diameter is designed to treat 75 m/hr. raw water and the detention time is 2 hrs. Find: 1) Radius and depth of the tank 2) Weir loading in m/m.d. pi g/cc, and u 1.3 c.p. 3) Diameter of the smallest settling particle is to be removed, if v=1.2 m/hr, p2 g/cc,
4. In a wastewater treatment plant, primary sedimentation tank (PST) designed at an overflow rate of 32.5 m³/day/m² is 32.5 m long, 80 m wide and liquid depth of 2.25 m. If the length of the weir is 75 m, the weir loading rate (in m³/day/m) is
Q3:calculate the head water at entrance of box culvert (2x2 m & 30 M length) shown in Fig.2 for discharge (Q=6m'/sec) Use the following data: -head loss coefficient at entrance ( Ke=0.5 )& for down stream (Kd-1 ) -Manning's coefficient n=0.013. Ke=0.5 HW S=0.3% 2.2m Kd=1 0.0 Fig2 L=30m
I neeeed a clear answer very fast in 15 min| dybala
Example A flow net for flow around single row of sheet piles in a permeable soil layer is shown in the figure. Given Sheet pile kx = k = k = 5xl10-3 cm/sec. Determine: 1. How high (above the ground 0 surface) the water will rise if piezometers are placed at points a, b, c, and d. 2. The total rate of seepage II II -4.5 Nr= 3 through the permeable layer per unit width. 3. The rate of seepage through the flow channel II per unit width (perpendicular to the section shown) -9.0 Datum Imnermeahle laver
The demand of water is 150 litres/head/ day in a city of one lakh population. The factor of safety is taken as 1.5, detention time as 4 h and overflow rate as 20,000 litres/day/m². The area of 3m deep plain sedimentation tank as per surface loading considerations will be
Design an earthen canal to carry a discharge of 40 cumecs and the mean diameter of silt particles is 0.3 mm.