-2X .380 1.42 1.48 (E) -1.52- 2X ø.340- 1.50- 4.51- Ø.360 B) .53 1.11 2.18 1.88 1.08- 49 1.06 - 2.22– 2.24 UNSPECIFIED TOLERANCES: 2-PL DEC (X.Xx)±.01 3-PL DEC (X.xxx)±.005 | OWN BY RAL HRS THIRD ANGLE PROJECTI REDRAWN BY R.SCHOFIELD SCALE NTS CHKD R.L.SWEET TITLE DWG NO. CORNER BRKT 1 1A01 ANGLES+O'3O' -2X 0.380 1.42 1.48 -1.52- 1.50- 2X ø.340 .51- 0.360 .53 1.11 2.18 L) 1.88 1.08- .49 -1.06 F) -2.22- 2.24 - UNSPECIFIED TOLERANCES: 2-PL DEC (X.XX)±.01 3-PL DEC (X.XXX)±.005 DWN BY MATERIAL HRS THIRD ANGLE PROJECTION REDRAWN BY R.L.SWEET R.SCHOFIELD SCALE CHKD NTS MŽ TITLE ANGLES+0'30' CORNER BRKT DWG NO. 11A015 94 Unit 4

-2X .380 1.42 1.48 (E) -1.52- 2X ø.340- 1.50- 4.51- Ø.360 B) .53 1.11 2.18 1.88 1.08- 49 1.06 - 2.22– 2.24 UNSPECIFIED TOLERANCES: 2-PL DEC (X.Xx)±.01 3-PL DEC (X.xxx)±.005 | OWN BY RAL HRS THIRD ANGLE PROJECTI REDRAWN BY R.SCHOFIELD SCALE NTS CHKD R.L.SWEET TITLE DWG NO. CORNER BRKT 1 1A01 ANGLES+O'3O' -2X 0.380 1.42 1.48 -1.52- 1.50- 2X ø.340 .51- 0.360 .53 1.11 2.18 L) 1.88 1.08- .49 -1.06 F) -2.22- 2.24 - UNSPECIFIED TOLERANCES: 2-PL DEC (X.XX)±.01 3-PL DEC (X.XXX)±.005 DWN BY MATERIAL HRS THIRD ANGLE PROJECTION REDRAWN BY R.L.SWEET R.SCHOFIELD SCALE CHKD NTS MŽ TITLE ANGLES+0'30' CORNER BRKT DWG NO. 11A015 94 Unit 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the drawing below, answer questions
Limits and tolerances
On the attached drawing 11A015, what is dimension H? All abbreviations are standard
Q. Based on the calibration curves, find out the respective sensitivities of the displacement measurement. 1. Strain (UE) Strain (UE) 0.01 0.00 -0.01 -0.02 -0.03 -0.04 0.0 0.01 0.00 -0.01 -0.02 0 -0.03 -0.0003-0.0009 -0.04 Strain vs. Displacement (Pushing) -0.0369*x + -3.1E-03 R² = 0.984 0.0 0:0063 -0.011 0.1 0.2 0.3 -0.0152 -0.0049 0.1 0.2 -0.0088 -0.0195 0.3 Strain vs. Displacement (Releasing) -0.0378*x + 2.16E-03 R² = 0.991 -0.0231 -0.0265 -0.0124 -0.0163- 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Displacement (in) -0.02 -0.0298 0.4 0.5 0.6 Displacement (in) -0.0325 -0.0235 0.7 -0.0272 -0.0352 0.8 -0.0379 -0.0318 -0.0379 0.9 1.0
I need questions 8, 9, and 10 answered pertaining to the print provided below.
No Go holes and H7/p6 tolerances
There are some incorrect indications in the following Fig.2. a) Re-draw a correct indicated drawing on the answer sheet. b) Describe the tolerance requirements of the corrected drawing. 0.01 7 0.01 B I0.01 B 60h 7 o.015 A
Please answer #83 82.Given a Ø24±0.25 hole located with a positional tolerance at LMC of Ø0.15, what is the positional tolerance at a produced size of Ø23.75? 0.15 0.25 0.40 0.65 83.What is the minimum edge distance between the surface of the hole in Question 82 and the outside surface of the part if the location dimension is 40 mm? 28.05 27.8 27.475 25.875
1. On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance that is implied between the diameters?
What part provides the most manufacturing tolerance and is easiest to work with, part 1 or part 2? Explain why.
What is the width of the vee groove?
On attached drawing 11A017 ,What is the length of the dovetail slot? All abbreviations are standard