2a. The delta strain gauge rosette shown in Figure 2a is attached to a structural component and measures the following strains: e, = 775x106, ɛz = 415×106, ɛ̟ =-515x10°. Determine the principal strain and principal stress components in both magnitude and direction given that the structure has a Young's Modulus of E = 200×10² N/mm? and Poisson's ratio of v = 0.3 . Show the directions of the principal stresses on a properly oriented stress element relative to the x,y coordinate system. 60° 60° 60° Figure 2a

2a. The delta strain gauge rosette shown in Figure 2a is attached to a structural component and measures the following strains: e, = 775x106, ɛz = 415×106, ɛ̟ =-515x10°. Determine the principal strain and principal stress components in both magnitude and direction given that the structure has a Young's Modulus of E = 200×10² N/mm? and Poisson's ratio of v = 0.3 . Show the directions of the principal stresses on a properly oriented stress element relative to the x,y coordinate system. 60° 60° 60° Figure 2a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 45° strain gauge rosette placed on a stainless steel structure results in the following values being determined for the maximum and minimum principal strains: €1 = 1,625.9 ×10–6 and €2 = -753.4 x10-6. Assuming plane stess, determine the factor of safety against the Tresca criterion. For stainless steel, use Young's modulus E = 196 GPa, Poisson's ratio v = 0.29 and yield stress oy = 1120 M Pa. Give your answer to 2 decimal places.
Figure below shows the bar with three equal elements. Use the finite element method and calculate: 2.1 the global stiffness matrix 2.2 the displacement on node 2, 3, 4 2.3 the Strain in each element 2.4 the stresses in each element using Hook's law and compare with theoretical stresses (o=F/A) (1) (2) (3) -50 N 10 mm 10 mm 10 mm A1=50 mm? A2=20 mm? A:=10 mm? E=200 GPa
If the displacements applied to a 3D isotropic material element is defined as functions of (x,y,z), Determine the following: 1- Stress at point (2,3,4). Assume E = 12.08 MPa and v = 0.25 2- Strain at point (1,2,2) 3- If you consider a plane stress condition for the above problems show how will the 2D assumption change the stress at the same point
A differential element on the bracket is subjected to plane strain that has the following components: , Ex = 300 x 10-6, Ey = 200 x 10-6, Exy = -500 x 10-6. Use the strain-transformation equations and determine the normal strain Ex' in the x' direction on an element oriented at an angle of 60°. Note, a positive angle is counter clockwise.
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
Q // The tensile tests were performed on longitudinal specimens of compact bone. The E1= 0.0004 65° strain rosette is mounted on a bone were the readings are obtained for each gauge as shown in figure. Determine (a) the principal strains and (b) the shear strain and average normal strain. 50° E2 = - 0.0005 65° €z = 0.0003
A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 4150 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L2 = 2,000 mm. Determine the normal strain in rod (2). (1) 4₁ Rigid bar (2) O 2849 μm/m O 3261 µm/m O 3071 µm/m O 3584 µm/m O 2594 μm/m B P L₂ C (1)
Incorrect A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ 12 d d₁ Undeformed Answer: dos = i 9810.3 R Calculate the deformation of diagonal QS. Deformed X mm
Q#7: The strains measured with a 60⁰ strain rosette are ϵa = R/3 x 10^-6 , ϵb= - R/2 x 10^-6 , and ϵc = R/8 x 10^-6 . Using E = 200 GPa and µ = 0.3, find the principal stresses and their directions. Show the results on a sketch of a properly oriented element. Use R=980 Note : For Clearance of Question Please Refer to Attached Picture.
The surface stresses of a pure aluminum device (E = 70 GP a, v = 0.33) that were tested on a space shuttle were obtained with stress sensors. The sensors were oriented as shown in Figure 3 and the unit strains obtained were εa = 1100 × 10−6, εb = 1496 × 10−6, and εc = −39.44 × 10−6.(a) What is the stress σxx in the x direction? Use Mohr's circle.
View Policies Current Attempt in Progress At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 180 MPa, o, = 50 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. y Ox At this point, determine the strain components &x, Ey, E, and Yxy. Assume that E = 73 GPa and v= 0.31 for the machine component. Ex = με Ey = με με urad Attempts: 0 of 3 used Submit Answer E₂ = Yxy= Save for Later