2a h 130 The diagram shows a ladder AB, of length 2a and mass m, resting in equilibrium on a vertical wall of height h. The ladder is inclined at an angle of 30° to the horizontal. The end A is in contact with horizontal ground. An object of mass 2m is placed on the ladder at a point C where AC = d. The ladder is modelled as uniform, the ground is modelled as being rough, and the vertical wall is modelled as being smooth. (a) Show that the normal contact force between the ladder and the wall i - mg(a+2d)/3 4h It is given that the equilibrium is limiting and the coefficient of friction between the ladder and the ground is V3. (b) Show that h = k(a+2d), where k is a constant to be determined.

2a h 130 The diagram shows a ladder AB, of length 2a and mass m, resting in equilibrium on a vertical wall of height h. The ladder is inclined at an angle of 30° to the horizontal. The end A is in contact with horizontal ground. An object of mass 2m is placed on the ladder at a point C where AC = d. The ladder is modelled as uniform, the ground is modelled as being rough, and the vertical wall is modelled as being smooth. (a) Show that the normal contact force between the ladder and the wall i - mg(a+2d)/3 4h It is given that the equilibrium is limiting and the coefficient of friction between the ladder and the ground is V3. (b) Show that h = k(a+2d), where k is a constant to be determined.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diagram below shows a rigid body ABC held in equilibrium by a ball-and-socket joint at A and three cables: BD, BE and CD. A 1.80 kN force is applied at F. The mass of ABC can be neglected. a) Draw a large, clear free-body diagram for ABC. b) Determine Cartesian component force equations of equilibrium for ABC
2. A "scale" is constructed with a (5A+4)-ft-long cord and the (20A+5B)-lb block D. The cord is fixed to a pin at A and passes over two small and frictionless pulleys at B and C. Determine the weight of the suspended block at B if the system is in equilibrium. NOTE: A is 2, B is 9 1 ft 1.5 ft D B
The smooth uniform rod ABAB is supported by a ball-and-socket joint at AA, the wall at BB, and cable BCBC. The rod has a mass of 19 kgkg . (Figure 1) 1. Determine the tension in the cable. 2. Determine the normal reaction at BB. 3. Determine the xx, yy, and zz components of reaction at AA using scalar notation.
A7,7 m long cable and a 54 kg mass block B are used to make a "scale." At A, the cable is attached to a pin, and at D and C, it goes through two little pulleys. If the system is in equilibrium at a = 1,7 m get the weight of the suspended block at B. b = 1 m b a B D.
J: the roof truss in Fig. 3, is supported by a roller at A and B. Find the value of the reactions. 20 KN 20 kN 20 kN 10 kN 10 kN 30 30 5 m 5 m 5 m 60 kN 50 kN Fig.3
Two uniform rods each with a mass m and length l are attached to gears as shown. For the range 0 < 0 < 180° determine the positions of equilibrium of the system, and state in each case whether the equilibrium is stable, unstable, or neutral.
5
8:27 Instagram H.W.2.jpg H.W.2 The homogeneous 100 N body A of Fig. is in equilibrium. Determine all unknown forces acting on the body. 30° A
#1 Subject: Statics of Rigid Bodies Last digit # to use: 1 Please answer logically with complete solution (and FBD hopefully), thank you so much!!!!!!
Two Cylinders where placed in a container and weighs 400lb and 200lb, with a dia. of 4 ft and 2ft respectively. Determine the reactions at points of contact of both cylinder and towards the container.
Problem 5 FN 4.5N K 20 B. 60 7.5N A small ring Pis threaded on a fixed smooth horizontal rod AB. Three horizontal forces of magnitudes 4.5N, 7.5N and FN act on P (see diagram). () Given that these three forces are in equilibrium, find the values of F and 0. (i) It is given instead that the values of F and 0 are 9.5 and 30 respectively, and the acceleration of the ring is 1.5 ms. Find the mass of the ring.
The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position