Table 1: Results of resistance testTerminalsMeasuredA BCresistance (2)Infinite (OC)А -ВA - C3.6В -D3.6В-СInfinite (OC)E - F9.9Infinite (OC)Infinite (OC)E - GF-GG - H9.9Figure 2: Transformer terminal layoutFigure 2 above shows the terminals of an unmarked split-winding transformer. The unknownterminals have been temporarily labelled A to H with masking tape.To determine the high voltage and low coils, the coils were identified using a continuity testerand their resistances measured. These results are presented in Table 1. (OC = Open Circuit)Use the information provided in Figure 2 and Table 1 to answer the following questions.26: The High Voltage (HV) coils are connected to which terminals?A.A-B and B-CВ.A-C and B-DС.A-E and B-FD.E-F and G-HE.E-G and F-H27. The Low Voltage (LV) coils are connected to which terminals?A.A-B and B-CВ.A-C and B-DC.E-F and G-HD.E-G and F-HE.A-E and B-F28. The transformer H1 terminal is which of the following?A.B.C.D.E.G.8

Answered: Image /qna-images/answer/6a3d8443-b0b9-450e-b0b6-b88688213eb0.jpg

26. The High Voltage (HV) coils are connected to which terminals? A. A-B and B-C В. A-C and B-D C. A-E and B-F D. E-F and G-H E. E-G and F-H 27. The Low Voltage (LV) coils are connected to which terminals? A. A-B and B-C В. A-C and B-D с. E-F and G-H D. E-G and F-H E. A-E and B-F 28. The transformer HI terminal is which of the following? A. A B. D C. E D. H E.

26. The High Voltage (HV) coils are connected to which terminals? A. A-B and B-C В. A-C and B-D C. A-E and B-F D. E-F and G-H E. E-G and F-H 27. The Low Voltage (LV) coils are connected to which terminals? A. A-B and B-C В. A-C and B-D с. E-F and G-H D. E-G and F-H E. A-E and B-F 28. The transformer HI terminal is which of the following? A. A B. D C. E D. H E.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Design a clamper to perform the function indicated. Determine the proper value of VDC Calculate the output voltage swing. a. b. 10 V -10 V Vi DESIGN Vo -1.3 V - 21.3 V u
13. A rotary standard with a K of % whr per revolution and a multiplier of 3 makes 42.4 revolutions during the testing of a watthour meter with a K,, of 1.8 whr per revolution. If the meter has two current coils connected in series and makes 48 revolutions, what is the percent registration of the meter under test? A. 79.5% B. 98.1% C. 119 % D. 102%
In a 3-phase 4-wire system, the currents in R, Y and B lines under abnormal conditions of loading are 11=100 A, (angle 30 degree), 12=300 A (angle 300 degree), 13=100 A (angle of 180 degree). The current in the neutral wire is: Select one: O a. None of above Ob. 13 A O c. 51 A O d. 150 A O e. 250 A
L.1. Which letter identifies the device used to supply power to the circuit in Figure A9?A. AB. HC. BD. C L.2. Which of the following will cause component A in Figure A9 to open?A. Increase in pressureB. Decrease in temperatureC. Increase in temperatureD. Decrease in pressure L.3. How many fan motors are operating given the conditions shown in Figure A9?A. 3B. 4C. 2D. 1 L.4. In Figure A9, if A opens how many fans would be operating in the circuit?A. 2B. 0C. 4D. 3
#4 please provide 4 decimal places in tha answer
02. Write LADDER and IL programme for below application? The objective of application 2 is to detect and sort 2 geometrically different components travelling along a conveyor. This is a common requirement in packing lines. The application is illustrated in Figure 2. Components labeled A and B travel along a conveyor. Component B is to be deflected by a sorting solenoid Y1 while component A is to be allowed to pass the sorting area. Two proximity switches, S1 and S2, are located at different heights to produce a sorting signal. The sorting solenoid is to be energized for 1 second to deflect all components of type B down a different conveyor feed path.
A 2-wire DC distributor XY is fed 350 meters long area in wapda town phase 2 Lahore. It is fed at point Block A. The various block loads and their positions are given below: Block C 40m 35A Block D 100m 40A Block E 150m 100A Block F 250m 50A If the maximum permissible voltage drop is not to exceed 13 V, Examine the cross-sectional area of the distributor. Take p = 1-78 x 10-8 Qm.
Problem #1 Consider the switching waveforms of the voltage and current of a resistive power switch circuit shown here. ,= Let: Vs=4KV, Is = 2KA, VSAT = 0.8 V, and ISAT = 1 mA Assume the switch turn-on to be (t2- t₁) and switch turn-off to be (t4t3), where t₁ = 2 μs, t₂ = 5 μs, tз = 19 µs, and t4 = 22 μs. The switching frequency is 100 Hz. 2= Compute the average dissipated power in the power switch. Thw average power is: Pdiss(Total) VSW A VSAT- isw Vs ISAT 0 t₁ t₂ 1 ·√ p(t)dt, where p(t) = Vsw(t).isw(t) Ts (sec) Is t (sec) VG Vs Rs w IG Power Switch +
Short circuit is occurred when: Select one: a. All answers. b. There will be a zero-resistance connection between terminal A and B and therefore the 2 terminals are at the same voltage. С. The voltage between the two terminals is zero although there may be a nonzero current between the terminals. d. A pair of terminals connected by a wire (of zero resistance).
A two-wire d.c. distributor AB, 600 metres long is loaded as distance from A (metres) : 150m, 300m, 350m, 450m and Loads in Amperes : 100A, 220A, 230A, 300A. The feeding point A is maintained at 440 V and that of B at 430 V. If distributor resistance of 0-02 Q per 100 metres. Examine: (i) The currents supplied from A to B. The power dissipated in the distributor. Point of Minimum potential (ii) (iii)
A patient is connected to a pressure monitor by way of a catheter. Resistance of catheter is 6000 Q. Dirt and grime make a resistance path from the catheter to H wire of 500,000 Q. The H wire is plugged into a 240 V power bus. Calculate the leakage current that could pass into the heart of the patient. Is the patient might or might not have shock? Assume a viscera resistance of 200 Q.
Figure shows a vehicle speed control example block diagram. Apply block diagram reduction and find?(?).