26/ For the following carbon fiber foot in the figure below, the foot length to the ankle joint is 25cm, foot average width is 8cm, foot average height is 1cm, if the foot modules of elasticity is 270Gpa, determine the foot tip deflection if the patient is walking at the (toe off) position as shown in figure. Assume the reaction force is 800N. 3-3

26/ For the following carbon fiber foot in the figure below, the foot length to the ankle joint is 25cm, foot average width is 8cm, foot average height is 1cm, if the foot modules of elasticity is 270Gpa, determine the foot tip deflection if the patient is walking at the (toe off) position as shown in figure. Assume the reaction force is 800N. 3-3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40kN. The modulus of elasticity for steel may be taken as 200 kN/mm2. Find stress, strain and elongation of the bar due to applied load.
Determine the torsion from the following figure. The torsional moment varies in the form of a parabola from 0 to t0 and t (x) = ax + bx + c, GJ is the axial stiffness.please i need help !!!!
The stress-strain plot of the polyester resin material is given in the figure. The AC beam is supported by the AB rod and CD column made of this material and is subjected to a single load of P = 80 kN. As the diameter of AB rod is 40mm and diameter of CD column is 80mm(a) What is the modulus of elasticity? Calculate the elasticity coefficient of the material whose stress-strain graph is given.(b) Find the slope of the AC rod after loading.
Problem 3: (MМ4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. a b Figure.4: Cross-section of a hollow-square steel column
Consider the steel truss and member cross-section presented in figures below. All the members of the truss have the same cross-section as shown in the figure to the right. They all also have a Young's Modulus of 210 GPa. What can the highest value of force F be before member AC fails by buckling? Force 1AN - 300 mm 40° 4 m $35 mm 7m 300 mm 8 m 35 mm 35 mm 35 mm Please provide your answer in kN.
Consider the two bars of identical material with their elastic modulus E as shown in Figure below. Both bars have the same circular cross-section with diameter of d. The length of the longer bar is 2L and the length of the shorter bar is L. The angle between the bars is B. The system is subjected to a vertical force acting at point Pas shown in the figure with a magnitude of F. Calculate horizontal and vertical components of the displacement of point P. Use engineering notation (ENG display mode on scientific calculators) with 3 significant figures after the decimal point. E (psi) 1.50E+06 d (in) 1.25 L (in) 12 Beta (degrees) 30 F (Ibf) 110 F P L 2L
In the system in the figure, the yield strength of the AB bar is 140 MPa and the diameter is 25 mm. plastic in the AB bar Calculate the load P that can be safely applied to the system without deformation (E: 200 GPa)
An iron rod 5 m long and having a 10 mm outside radius and 4 mm inside radius stretches 1 mm when a mass of 255 kg hangs on it. Compute the modulus of elasticity of the iron. note: answer must be in GPa
Calculate the Force P applied according to the spring compression 0.02 m with the spring stiffness coefficient K=4 kN/m under the influence of the Force P applied to the cable in the figure?
L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is subjected to loads of PR = 112 kN and Pe = 18 kN. Segments AB and BC have elastic moduli of E, = 206 GPa and E = 73 GPa. The rod has circular cross-sections, and the dimensions of the rod are given above. Find the overall change in length of the rod under this load. Assume: • The collar at B is rigid • Stress concentration effects may be neglected 2014 Michael Swanbom
The simply supported beam is subjected to the loads as described in the figure and parameter table. Neglecting the thickness of the beam, calculate the horizontal and vertical support reactions at A and B. F A B C -4*- L3 parameter value units L1 L2 L3 ft 4 ft 6 ft theta 65 F 200 lb M 500 lb-ft For the answers, take to the right and up to be the positive directions. The support reaction at A in the z direction is NAz- lb The support reaction at A in the y direction is NAy- lb The support reaction at Bin the z direction is NB= lb The support reaction at Bin the y direction is NBy= lb
(a) Calculate the total elastic strain energy stored in the material of the pin-jointed structure shown in Figure Q4(a). The structural members cach has a cross sectional area A, elastic modulus E, shear modulus G, moment of inertia I and polar moment of inertia J. B L. A 45 30 Figure Q4(a) (b) An elastic structure with flexural stiffness El is pinned at A and fitted with a roller at end C, as illustrated in Figure Q4(b). The structure carries a uniformly distributed load w (force per unit length) on member AB. (i) Determine the reaction at the roller support C, in terms of w and R. Using Castigliano's energy theorem, determine the horizontal displacement of end C of the structure. Consider bending effecis only. R Figure Q4(b)