250 mm AT

Q: he mechanism below has a crank that revolves clockwise at point O at a speed of 2000 rpm. B 1.2 kg…

A: Angular acceleration and linear acceleration of links need to be evaluated.

Q: Two friction discs A and B will come into contact, without slipping, when the angular velocity of…

A: rA = 150 mm = 0.15 m rB = 200 mm = 0.2 m N = 310 rpm

Q: D The pin at B is free to slide along the circular slot DE and along the rotating rod OC. Assuming…

A:

Q: In a mechanism that is a combination of a four-bar mechanism and a slider-crank mechanism. Slider A…

A:

Q: Two friction disks A and Bare to be brought into contact without slipping when the angular velocity…

A: Calculate the velocity of the contact point. V= RA*WA = 0.15*(2*3.14*380/60) =1.9 π m/s Calculate…

Q: Two friction disks A and B are to be brought into contact without slipping when the angular velocity…

A: Write the given data:

Q: Two friction disks A and B are brought into contact when the angular velocity of disk A is 240 rpm…

A: Given Diameter of disc A is 150 mm = 0.15 m RPM disc A = 240 rpm Counter clockwise Diameter of disc…

Q: In a continuous printing process, paper is drawn into the presses at a constant speed v. Denoting by…

A: Given data as per the question The radius of paper roll = r The thickness of paper = b calculations

Q: The rotor of a gas turbine is turning at a speed of 6,300 rpm when the turbine is turned off. It is…

A: Speed = 6300 rpm Time = 8 minutes

Q: assumed to be a 1.2-kg uniform slender rod and is attached to the 1.8-kg piston P. During a test of…

A: Given Data⇒Slider crank mechanisml=250 mm=0.25 mb=100 mm=0.1 mω=320 revmin=5.33revsθ=90°Problem…

Q: The rated speed of drum B of the belt sander shown is 2400 rpm. When the power is turned off, it is…

A: Given Data: The radius of the drum B is r = 25 mm. The radius of the drum C is r = 25 mm. The rated…

Q: A 1-lb ball A and a 2-lb ball B are mounted on a horizontal rod which rotates freely about a…

A: Solution: Given Data: mA=1 lbmB=2 lbri,A=10 inrf,A=10 inri,B=8 inrf,B=16 inVi,A=8 ft/s   To Find:…

Q: In the engine system shown l = 250 mm and b = 100 mm. The connecting rod BD is assumed to be a…

A: GivenN = 400 rpm(c.w)l = 250 mm = 0.25 mb = 100 mm = 0.1 mmBD = 1.2 kg , mP= 1.8 kgθ=90°

Q: A simple friction drive consists of two disks A and B . Initially, disk B has a clockwise angular…

A:

Q: 1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and…

A:

Q: The system shown is held at rest by the brake-and-drum system shown. After the brake is partially…

A: Given data Distance traveled by the cylinder after 4.5 s, S = 5 m. The radius of the drum, r = 250…

Q: The flywheel (I = mk² ) shown has a radius of 20 in. a weight of 250 lbs, and a radius of gyration…

A: Part aAs per above given diagramtaking moment at B but External forces=effective forcesso we…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: N=600 rpmt=4s

Q: In the engine system shown l = 250 mm and b = 100 mm. The connecting rod BD is assumed to be a…

A: Given, θ=900 l=250 mm=0.25 mb=100 mm=0.1 m N=400 rpm

Q: 3 A load is to be raised 20 ft by the hoisting system shown. Assuming gear A is initially at rest,…

A: Given : rA=3 in, rB=18 in

Q: In the engine system shown l = 250 mm and b = 100 mm. The connecting rod BD is assumed to be a…

A: In a slider-crank mechanism, velocity and acceleration can be obtained by two approaches 1)…

Q: A simple friction drive consists of two disks A and B. Initially, disk B has a clockwise angular…

A: Given Data: Initial angular velocity of disk B ωiB=590 rpm=590×0.10472=61.7848 radsec Disk B stops…

Q: Disk A has a mass of 6 kg and an initial angular velocity of 360 rpm clockwise; disk B has a mass of…

A: Mass of disk A, mA=6 kg,Mass of disk B, mB=3 kg,Initial Angular velocity of disk A, ωA=360…

Q: The grooved drums in the two systems shown are identical. In both cases, (a) and (b), the system is…

A: Angular velocity of drum can be determine after 4 seconds of rotation by the principle of…

Q: 7 αA A 1B B D -1'p'

A: Given system,

Q: The motion of an oscillating flywheel is defined by the relation 0 = 0ne-3t that e o cos 4t, where 0…

A:

Q: The rotor of a gas turbine is turning at a speed of 5,600 rpm when the turbine is turned off. It is…

A: speed of the turbine N=5600 rpmtime taken to come to rest  t=5 min=5×60=300s

Q: The 200-mm-radius disk rolls without sliding on the surface shown. Knowing that the distance BG is…

A:

Q: The uniform rods AB and BC weigh 2.4 kg and 4 kg, respectively, and the small wheel at C is of…

A: Given: mAB=2.4 kgmBC=4 kg Vc= 2 m/s rotation of link AB =90 degree To determine: determine the…

Q: Two friction wheels A and B are both rotating freely at 300 rpm counterclockwise when they are…

A: The angular velocity of disk  B is  ωB0=300 rpm=31.416 rad/s At t=12 secωB=75 rpm=7.854 rad/s…

Q: Problem (2) A turntable is used to test an intentionally weak adhesive by coating the bottom of a…

A: Given data: The mass of the block is m = 0.3 kg. The distance of the block from the center of the…

Q: The 300 mm yellow rod AB is guided by red wheels at A and B that rolls in vertical and horizontal…

A: Given: The length of rod AB, L = 300 mm The angle made by rod with horizontal, θ = 30o The constant…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.