2400 kg 15m Question # 1. A fixed crane has a mass of 100-kg and is used to lift a 2400-kg crate. It is held in place by a pin at A and a rocker at B. The center of gravity of the crane is located at G. Determine the components of the reaction at A. Az = -10933.3N - Ay = 3400N ↑ Az = 10708 N + Ay = 3331 N ↑ Az = 95484 N + Ay = 24525 N ↑ Ax = 0 Ay = 23544N ↑

Q: If the block is held in the equilibrium position shown, determine the mass of block D. dm C -d₁ m.…

A: Let's first calculate spring AB's stretched length. The Pythagorean theorem may be used to determine…

Q: The light right-angle boom which supports the 260-kg cylinder is supported by three cables and a…

A: The mass of cylinder is m=260 kg

Q: The gusset plate is subjected to the forces of three members s shown in. The forces are concurrent…

A: To find The magnitude of the tension force in member C.  The angle  Given The force on point O due…

Q: platform scale consist of a combination of third and first class levers so that the load on one…

A: The free-body diagram for AB is-The moment equilibrium condition about point A-

Q: A puck weighs 17 lb and rests on the center of the frictionless surface of the ramp supported in…

A:

Q: Determine the magnitude (in Ibs) of the external reaction at the main cable support DE.

A: Consider the diagram as shown below for the given truss system.

Q: Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last…

A:

Q: Determine the reactions at supports A and B. a=5.9 ft b=9.7 ft c=9.5 ft d=8.3 ft A 500 lb/ft C 700…

A:

Q: Determine the horizontal and vertical components of reaction at pin C. Take that P₁ = 450 N and P₂ =…

A: Given that: P1 = 450 N P2 = 540 N It is required to determine the horizontal and vertical component…

Q: Q2/ Determine the unstretched length of spring AC if a force P 801b causes the angle 0 = 60° for…

A: Solution:

Q: The following figure (5.12 from the text) shows a truss with several zero force members. Identify…

A:

Q: The 60-lb door shown in Figure 1) has its center of gravity at G. ▾ Part A Determine the components…

A: Given data is

Q: Draw a complete free-body diagram for the system. Calculate the reactions at both supports needed…

A: i) Free body diagram where, RA= Vertical reaction force at A            RC= Vertical reaction force…

Q: 3. Three kids stand on a see-saw as shown. The see-saw has a uniform cross section and weighs 10 lb,…

A: Given Data  mA= 30 lb mB= 40 lb mC=20 lb

Q: 1. Plate ABCDEF is a sliding door supported by a frictionless linear bearing at A and a frictionless…

A: The total weight of gate is

Q: The uniform 14-m pole has a mass of 190 kg and is supported by its smooth ends against the vertical…

A:

Q: can you helpe me pleas to find Ax, Ay, ND, NC60 lb-ft A 3 ft C G 4 ft B D 0.5 ft Determine the force…

A:

Q: Question 1 Neglecting the weights of the bar and the pulley and assuming the weight of the ball B to…

A:

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: The crane truck has a weight of 14250 lb and a center of gravity at point CG. The parking brake only…

A: To finddetermine the maximum force F applied at the angle  that can be exerted on the crane without…

Q: 600 lb C 18 25 750 lb-ft B 10 900 lb| Dimensions in inches

A:

Q: The drop gate at the end of the trailer has a mass of 124 Mg and mass center at G. It is supported…

A:

Q: A "scale" is constructed with a 4.1-ft-long cord and the 13-lb block D. The cord is fixed to a pin…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.