Within few minutes 24. Determine the maximum tensile, compressive, and shear stresses at points A and B on the bicycle pedal crankveisshown in the figure."The nedal and crank are in a horizontal plane and points A and B are located on the top of the crank. The loadON acts in the vertical direction and the distances (in the horizontal plane) between the line of action of theload and points A and B are b,= 125 mm, b260 mm and bz = 24 mm. Assume that the crank has a solid circu-P = 750 NCrankd = 15 mmab = 125 mm%3DA b3= 24 mmb2 = 60 mmBAb3-b2Top view

Answered: Image /qna-images/answer/71ce04e6-ab9c-4ef1-8342-5e7dd74ab19e.jpg

24. Determine the maximum tensile, compressive, and shear stresses at points A and B on the bicycle pedal crank ve is shown in the figure. The pedal and crank are in a horizontal plane and points A and B are located on the top of the crank. The load 750 N acts in the vertical direction and the distances (in the horizontal plane) between the line of action of the load and points A and B are b1 = 125 mm, b2: lar cross section with diameter d = 15 mm. = 60 mm and ba = 24 mm. Assume that the crank has a solid circu- P = 750 N Crank d = 15 mm b1 = 125 mm b3 = 24 mm b7 = 60 mm tb3 A b3 b2 Top view

24. Determine the maximum tensile, compressive, and shear stresses at points A and B on the bicycle pedal crank ve is shown in the figure. The pedal and crank are in a horizontal plane and points A and B are located on the top of the crank. The load 750 N acts in the vertical direction and the distances (in the horizontal plane) between the line of action of the load and points A and B are b1 = 125 mm, b2: lar cross section with diameter d = 15 mm. = 60 mm and ba = 24 mm. Assume that the crank has a solid circu- P = 750 N Crank d = 15 mm b1 = 125 mm b3 = 24 mm b7 = 60 mm tb3 A b3 b2 Top view

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Estimate the DEC and TIC of an ESP with 50,000 m2 of net plate area. Calculate your answers in 1998 dollars, then estimate the 2002 TIC,
what is the design strength? steel material The size of the hole = 22mm sectional area = 1650mm^2
Convert 2500 inches /hour to feet/ min
The mean is-1 Freg 2 Classes 50-54 55-59 60-64 65 69 4 21
Engineering Utilities 2 Compare and contrast Active Fire Protection System and Passive Fire Protection System
On a roll of tape 36” wide x 150’ long, there is an equivalent of ______ square feet.
kindly solve asap
1.How many days will it take you to consume a 10-m^3 of water if your daily consumption is 30 liters?2.How many tiles would be needed to cover a 30ftx28ft floor area if a tile measures 30cmx30cm?How many tiles will you buy?3. How many pieces of plywood would be used to cover the ceiling in #2 if the measurement of the ceiling is the same as the floor area and if a plywood measures 1.22 m x 2.44 m? How many pieces of plywood will you buy?4.An Aquarium measures L=5ft, 3ft and H= 20 inches.How many liters will it contain if it will be filled with water until 2 inches below its brim?5.An atom has a diameter of 3.5x10^-10m.What is the measurement in a.)cm and b.) nm6.What is the equivalent speed of light which is 299792458.0 m/s to:a)km/hb)nm/usc)cm/nsd)um/s7.A book measure L=10 inches, W= 8 inches, and H=2 inches.How many of these can be packed in a box that measures L=50cm,W=50cm, and H=60cm if it is to be filled up to the maximum number (this means that no book or any part of it can be…
Define the following: i. Solvent ii. Solidus line
I need answer within 20 minutes please please with my best wishes
Help pls