24 KN 0,6m 1.2 m D 1.5 m 12 KN .0.3m 1.2 m A E B

Q: = constant 5. Bernou lli's equation is expressed as asY'2g Research on the corresponding units por…

A:

Q: Use Virtual Work Method to answer the questions below considering the truss shown. Use the…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: The cross section of a beam made to carry vertical transverse loads is shown. Which pair of elements…

A:

Q: Solve for the x-component (in mm) of the centroid if that a=2.4, b=2.2, c=4.8, d=9.7, and r=1.6. All…

A:

Q: The force of F = 55 lb acts along the edge DB of the tetrahedron shown in (Figure 1). Figure 8 ft 10…

A:

Q: m in the following Figure. = members (including the beam) are el data: E, I, a E, A, a P

A:

Q: The torque (N-m), T, delivered by a water turbine depends upon the discharge (m³/s), Q, head (m), H,…

A: The number of terms is 6.

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: It is given that,

Q: A wooden bar beam arrangement is shown in the figure. The beam is formed by nailing wooden bar and…

A: Given,B = 200 mm H = 360 mm t = 20 mm F = 250 NV = 3.2 kN or 3200 N

Q: 15 (b) 2

A:

Q: Explain the meaning of stresses σyy and τxy . Use diagrams to illustrate

A: Given StressesTo find out Meaning and illustration

Q: What is the member force in CD? Indicate the negative (-) sign in your answ the member is in…

A:

Q: A high-strength bolt that is passing through a steel plate is subjected to a tension force of P=4.6…

A: A) Given Data: Diameter of the bolt is db=12 mm. Diameter of the hole is D=14 mm. The tensile force…

Q: Determine the stability and determinacy r C * r = || V C Classification

A: Draw the Free body diagram of the beam parts showing unknown reactions. Then count the number of…

Q: 2= Projectile Mass m₂ 0 m₁ = Counterweight mass Ah

A: Given Data: The counterweight mass is m1. The projectile mass is m2.

Q: 1. The bar AB with cross section Ag is shown in the figure, the strength condition is just…

A:

Q: A Given the FLEXURAL beam shown=6000 RIGIDITY of the KN.m^2, find the :deflection at the roller…

A: Roller support is a support condition in which vertical movement is restrained while the rotation…

Q: ent, node and mesh. AE 1000 L AE 100 10

A:

Q: A beam is subjected to equal bending moments of M₂ = 2800 N.m. The cross-sectional dimensions are b…

A: The bending moments of Mz = 2800 Nm. The cross-sectional dimensions are b = 150 mm  c = 27 mm d = 72…

Q: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

A: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

Q: The intensity applied to beam AB is increased by a factor of 2. (i.e. your answer for the ntensity…

A:

Q: UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer…

A: Given values: Consider the section of beam given. Moment, M = 3000 kip-in a= 4 in   The equation of…

Q: d a --x -d-

A:

Q: The beam has a Young's modulus of Eo =100 GPa, a length of 1 = 4 m and 2nd moment of area of I₂ = 4…

A: Given: E = 100 GPa = 100 x 109 N/m2 Iz = 4 m4 l = 4 m w = 100 N/m

Q: The cross section of a beam made to carry vertical transverse loads is shown. Which element does NOT…

A: this question is asking about which element of cross  section is not going to take verticle…

Q: The profile above depicts two joined profiles, each of width h. Find the centroid, X. of the total…

A:

Q: A constant stress cantilever beam having a point load at the end is desired. The width b of the…

A:

Q: At a temperature of 44°F, a 0.06 in. gap exists between the ends of the two 6/°F] and bar (2) is…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A: Step 1: Given:σx​=10ksiσy​=29ksiτxy​=6ksiTo Find σx′​,σy′​ and τx′y′​ when θ=+40∘(anticlockwise)Step…

Q: eral steps that -node and mes

A: solution of above problem is below:

Q: Determine reactions at A and B .

A:

Q: 90 MPa 55 MPa 70 MPa 55 MPa 90 MPa 65° TE 70 MPa The state of stress on an element relative to the…

A: Given :   Required : Original state of stress and angle of rotation  Stress at rotated element…

Q: outer diameter of d = 24 mm. Determine: A) the maximum value of P before the shear stress in the rod…

A: A) Given data : Diameter of metal plate = 17 mm Diameter of the bolt = 12 mm Thickness of plate = 9…

Q: Situation #2 Classify each of the structures as statically determinate, statically indeterminate, or…

A:

Q: (4) As shown in the figure, the three steel plates are subjected to tensile force P, and seven…

A: When two plate is connected by single plate at middle and it is connected by means of rivet or bolt…

Q: A wooden bar beam arrangement is shown in the figure. The beam is formed by nailing wooden bar and…

A: For a wooden bar beam arrangementThe beam is formed by nailing wooden bar and each nailshearing…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: P=110 N

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.