How to solve I need do fast typing clear urjent no chatgpt used i will give 5 upvotes pls full explain 23. Calculate the wire diameter of a steel spring that could support a load of 50 kg. Allowable working stress is427 x 10 N/m², the spring mean diameter is to be 44.45 mm and G-79.3 Gpa.A. 0.2106 inB. 0.3028 in C. 0.3924 in D. 0.6931 in

Answered: Image /qna-images/answer/efa1012c-f944-45c6-81db-6e6c5a8406cd.jpg

Answered: 23. Calculate the wire diameter of a…

EBK CONTEMPORARY FINANCIAL MANAGEMENT

14th Edition

ISBN:9781337514835

Author:MOYER

Publisher:MOYER

Chapter14: Capital Structure Management In Practice

Section14.A: Breakeven Analysis

Problem 7P

See similar textbooks

Similar questions

5.6.2AW14 x 109 beam of A 992 steel with lateral support at 10-foot intervals. Assume Cb = 1.0 and determine the nominal flexural strength
I need typing clear urjent
02 (20 Marks): Use the Problem Table Method to calculate the Pinch Temperatures a values of QHmin and Qcmin and maximum energy recovery (MER) from the data below. Stream Stream Supply number type Target Temperature Temperature Heat Duty MW C °C 1 Hot 150 30 7.2 2 Hot 40 40 10 3 Hot 130 100 3 45 Cold 150 150 10 Cold 50 140 3.6 5 ATmin = 10°C
Four long, parallel conductors carry equal currents of = 1.00 A. The figure below is an end view of the conductors. The current direction is into the page at points A and B and out of the page at C and D. A × C B(x (a) Calculate the magnitude of the magnetic field at point P, located at the center of the square of edge length = 0.200 m. με
I need typing clear urjent no chatgpt used i will give 5 upvotes pls full explain
possible Standard material cost per kg of raw material is $8.75. Standard material allowed per unit is 6 Kg. Actual material used per unit is 6.25 Kg. Actual cost per kg is $8.00. What is the standard cost per output unit? O A. $48.00 B. $52.50 C. $50.00 D. $54.69 A: S Next
Read the question carefully and give me right solution according to the question
A manual assembly line is being designed for a product with annual demand = 100,000 units. The line will operate 50 wks/year, 5 shifts/wk, and 7.5 hr/shift. Work units will be attached to a continuously moving conveyor. Work content time = 42.0 min. Assume line efficiency E = 0.97, balancing efficiency Eb = 0.92, and repositioning time Tr = 6 sec. Determine: (a) hourly production rate to meet demand, (b) number of workers required.
Suppose that Motorola uses the normal distribution to determine the probability of defects and the number of defects in a particular production process. Assume that the production process manufactures items with a mean weight of 10 ounces. Calculate the probability of a defect and the suspected number of defects for a 1,000-unit production run in the following situations. a. The process standard deviation is 0.15, and the process control is set at plus or minus one standard deviation. Units with weights less than 9.85 or greater than 10.15 ounces will be classified as defects. b. Through process design improvements, the process standard deviation can be reduced to 0.05. Assume that the process control remains the same, with weights less than 9.85 or greater than 10.15 ounces being classified as defects. c. What is the advantage of reducing process variation, thereby causing process control limits to be at a greater number of standard deviations from the mean?
A 1.4-kg decoration hangs from the three wires as shown in the figure. The wire on the left makes an angle ax = 66.5° with the ceiling. The wire on the right makes an angle B-37.11° with the ceiling. The wire on the left has a tension that is twice that of the tension in the wire on the right. Part A What is the tension in the vertical wire attached to the decoration? This value is used in the next part, so use 4 significant digits. FT Value Submit Request Answer Part B ? Units a B
C (Ib/gal) - 5.8. A mixing process may be described as follows: A stream with solute concentration Ci (pounds/volume) is fed to a perfectly stirred tank at a constant flow rate of q (volume/time). The perfectly mixed product is withdrawn from the tank, also at the flow rate q at the same concentration as the material in the tank Co. The total volume of solution in the tank is constant at V. Density may be considered to be inde- 2.1 2.0 1.9 1.8 1.7 W FIGURE P5-8 10 6:30 A.M. Time 6:52 A.M. pendent of concentration. A trace of the tank concentration versus time appears as shown in Fig. P5-8. (a) Plot on this same figure your best guess of the quantitative behavior of the inlet concentration versus time. Be sure to label the graph with quantitative infor- mation regarding times and magnitudes and any other data that will demonstrate your understanding of the situation. (b) Write an equation for C; as a function of time. Data: tank dimensions: 8 ft high by 5-ft diameter Tank volume V: 700…
1

SEE MORE QUESTIONS

Recommended textbooks for you

EBK CONTEMPORARY FINANCIAL MANAGEMENT

Finance

ISBN:

9781337514835

Author:

MOYER

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Essentials of Business Analytics (MindTap Course …

Statistics

ISBN:

9781305627734

Author:

Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Publisher:

Cengage Learning

EBK CONTEMPORARY FINANCIAL MANAGEMENT

Finance

ISBN:

9781337514835

Author:

MOYER

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Essentials of Business Analytics (MindTap Course …

Statistics

ISBN:

9781305627734

Author:

Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

23. Calculate the wire diameter of a steel spring that could support a load of 50 kg. Allowable working stress is 427 x 10 N/m², the spring mean diameter is to be 44.45 mm and G-79.3 Gpa. A. 0.2106 in B. 0.3028 in C. 0.3924 in D. 0.6931 in