23 - Mathematical model of control system is ... A) mathematical expression of a system which has not a memory and output variables O B) mathematical expression of a system in that the variables are time-independent C) Mathematical expression which describes the relationships among system inputs, outputs and other i O D) mathematical expression of a system which describes interconnection via inner variables E) mathematical expression of a system which has a memory and input variables

23 - Mathematical model of control system is ... A) mathematical expression of a system which has not a memory and output variables O B) mathematical expression of a system in that the variables are time-independent C) Mathematical expression which describes the relationships among system inputs, outputs and other i O D) mathematical expression of a system which describes interconnection via inner variables E) mathematical expression of a system which has a memory and input variables

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Would it be b,d, and c? 2. Which of the following are characteristics of a closed loop control systems? Select allthat apply.a) Low sensitivity to changes in system parametersb) Higher accuracyc) Good regulation against disturbancesd) Reliabilityd) Slower response to inputs.
advantages and disadvantages of pi controllers in control systems. Could an example with temperature control for a human occupied building be provided?
5) Error ep (%) h 1 1 a. Draw a plot of the controller output. 3 t(s) Proportional-Integral (PI) mode controller with parameters; K₂=5, K-1 s¹ and P(0)=20 %. a. Find the controller output for each time. intervals.
which of the following test functions modelling? function time. cen be used for system Assume aas A. Ō Ct) B. Sinut C, ut) Cusut tult)
Resistive displacement sensor is: a. transduces that containing resistant that slides against another fixed resistive element. O b. electromechanical device containing an electrically conductive wiper that slides against a fixed resistive element. c. electromechanical device containing an electrically capacitive wiper that slides against a fixed element. d. mechanical device containing wiper that slides against a fixed resistive element.
5.- Design a microcontroller system to control a sprinkler controller that performs the following tasks. We assume that your microcontroller is clocked at 10 MHz and has a 16-bit free-running counter. The sprinkler controller system controls two different zones by turning the sprinklers within each zone on and off. To turn on the sprinklers in a zone, the controller needs to receive a 152.589 Hz PWM signal from its microcontroller. To turn off the sprinklers in the same zone, the controller needs to receive the PWM signal with a different duty cycle. B.- After 15 min, your microcontroller must send the PWM signal with a 15% duty cycle of 10 ms to turn off the sprinklers in zone one.
Q.14 Consider the following Assembly Language program. MVI A, 30 H ACI 30 H XRA A POP H After execution of the above program, the contents of Accumulator will be (. -)10-
Choose the correct statements. Select one or more: a. Specific energy expressed with SI base units is J/K. Ob. Dynamic model of a measurement element with second order system dynamics can be expressed with block diagram using only scalar multiplication blocks. c. Feedback can make stable system unstable. Od. A Pl-controller is a controller with four parameters (proportional gain, integration time, derivate time and derivate filter). e. Second order system is a system that's step response oscillates when it have (underdamped) complex valued poles. Of. A thermocouple is one example of non-linear type of sensors. Og. Drift and non-linearity are wanted properties for sensors. Oh. Measurement uncertainty is only caused by external sources. Oi. A Bode diagram is a graphical representation of frequency response that consist of two separate plots (one for magnitude and other one for phase). Oj. A filter is one example of functionality that can be part of signal processing element.
i need the answer quickly
A temperature sensor operates in the range of 0 to 80 degree Celsius and it is converted into voltage output between 0 to 8 volt. If the 4 bits ADC is used, then answer the following questions. 1) Draw a quantization map 2) If the temperature is 20 what will be the digital output from ADC, show your computation. 3) If we pass through result from ADC back to DAC what is the temperature value. Show detail computation.
3. The functions of the control system is monitored by the 8-bit length microcontroller which has in-built digital to analog converter. The controller behaves as fully open stage and output of the digital word 1111 1111, when a maximum voltage of 6 V is applied to the controller. i) calculate the change in voltage when there is a change in 1 bit in input, ii) Calculate the total analog output voltage for the input digital value 0000 0010.
i need the answer quickly