22. In a bakery, water is forced through pipe A at 150 liters per second. Oil (sg = 0.8) is forced through pipe B at 30 liters per second. Assume ideal mixing of incompressible fluids and the mixture of oil and water form globules and exits through pipe C. Evaluate the specific gravity of the mixture exiting through the pipe C. a. 0.385 c. 0.976 b. 0.257 d. 0.865 23

22. In a bakery, water is forced through pipe A at 150 liters per second. Oil (sg = 0.8) is forced through pipe B at 30 liters per second. Assume ideal mixing of incompressible fluids and the mixture of oil and water form globules and exits through pipe C. Evaluate the specific gravity of the mixture exiting through the pipe C. a. 0.385 c. 0.976 b. 0.257 d. 0.865 23

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Liquids A, B and C, in the containers shown, have SG of 0.80, 1.00 and 1.60 respectively. What is the pressure at the bottom of the tank? hA EL. 8 A (SG = ha EL. 6 B (SG = hc EL. 2 C (SG = EL. O a. 85.382 kPa O b. 86.328 kPa c. 86.382 kPa d. 89.328 kPa
3. Given a liquid with a specific gravity of 0.82 flows through a 100-mm pipe 308-m long at a rate of 32 liters per second. Assuming a viscosity of 0.0052 Pa-s a. Calculate the Reynold's number. b. What is the total head loss in meter if f= 0.021? MAI opy
1. A block, 1ft square and 9 inches deep floats on a stratified liquid composed of a 6in layer of water above a layer of mercury. Determine the weight of the block if the position of its bottom is 1 inch below the mercury. 2. At point A in a pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. At point B, 2m lower than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. Show detailed computation. 3. What is the hydraulic radius of the channel shown: 1.5m 1.5h 4. wty A vertical right-angled triangular surface has a vertex in the free surface of a liquid. Find the force on one side. 1.5m 1:2m
Good day. Here is my question (3) The diameter of a horizontal tube is 4 in., in which tetrabromoethane (spec. grav. = 0.30) is flowing at the rate of 0.50 cu ft. per sec. The pressure is 30 lb. per sq. in. (gage). If the tube gradually decreases to 3 in. in diameter, what is the pressure there?
The tank contains a liquid having a density of 2.52 slugs/ft^3 10 in 5 ft 10 ft. 7 ft Pliquid 2. 52 slugs/ſt³ %3D a. Determine the unit weight of the liquid when it reaches the indicated level. b. Determine the liquid's weight. Use English units to express your response. c. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured into the tank, will it sink to the bottom, or will it float on the surface of the liquid, or will it be suspended in the liquid?
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
1. Oil flows through a 200 mm diameter pipe A at 2 m/s and through a 250 mm diameter pipe B at 1 m/s and discharges through a 150 mm diameter pipe C. Specific gravity of oil are 0.9, respectively. a) Determine the discharge at pipe C. b) If alcohol flows through pipe B. Determine the average density of the two fluids as the mixture flows through the pipe at C. Specific gravity of alcohol is 0.78. B ↑
In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
Problem 5 Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5 ft³/s. What is the pressure at section 2 when the pressure at section 1 is 18 psig and the head loss is 9 ft between the two sections? Assume α = 1.0 at all locations. Vertical A₁ = 0.80 ft² 12 ft 4₂ = 10.20 ft²
Heavy fuel oil flows from A to B through 3000 ft of horizontal 6-in steel pipe. The pressure at A is 155 psi and at B is 5.0 psi. The kinematic viscosity is 0.00444 ft2/s and the specific gravity is 0.918. (a) What is the head loss (ft) between A and B? (b) Assuming laminar flow, what is the velocity (ft/s) of oil from A to B? (c) What is the flow rate (ft3/s) assuming laminar flow? (d) Is the flow really laminar? Prove by solving the Reynolds Number.
B- A thickener is designed to separate suspension containing 15 Kg of water/Kg of solid is to be thickened to a sludge containing 4.5 Kg of water/Kg of solid in a continuous operation. Calculate the minimum area of a thickener required to effect the separation of mass rate of feed of 103 Kg/s of solid? p H₂0 = 1000 kg/m³ ps = 6000 kg/m³ De=0.002 m R' pu 10% 10³ 10² 10 100% 101 10 2 10:3 Region a 10 2 10 1 TELEGRAM MOTION OF PARTICLES IN A FLUID 10° Region b 10 R puz Region c = 0.22 10² Re' R/pu² versus Re' for spherical particles 10³ 10⁰ 105 Region d 10 10
A pipe carrying oil of specific gravity 0.88 changes in size from 150 mm in diameter at section 1 to 450 mm in diameter at section 2. The section 1 is 4.2 meters below section 2. The pressure at section 1 is 90 kPa and 60 kPa at section 2. If the discharge is 150 liters per second, determine the head lost in the system. Select one: O a. 2.49 m O b. 2.21 m O c. 2.90 m O d. 1.98 m