22 = 150 ft 21 = 50 ft D = 6 in Pump

Q: If the rectangular tank full of water in Fig. P3.37 has itsright-hand wall lowered by an amount δ ,…

A: The time required to reduce the excess water level depends upon the outer flow of the tank, volume…

Q: ) the volumetric flow rate, Q, in each exit branch in units of L/s ) the velocity, V, in each exit…

A:

Q: I nree pipes steadiy aenver water at 20°C to a large exit pipe in Fig. P3.8. The velocity V, = 5…

A:

Q: Water flows through a pipe, which is 30 mm in diameter and 55 m long, ab 2,75 m/s. Using Darcy's…

A:

Q: Consider a geyser that shoots water to a height of 28 m into the air. Density of water, rho = 1000…

A: Given Data : Height of water Geyser shoot y2 : 28m Density of water ρ : 1000 kg/m3  acceleration…

Q: A typical pump has a head that, for a given shaft rotationrate, varies with the fl ow rate,…

A: Given, The elevation at section 1, Z1 = 50 ft The elevation at section 1, Z2 = 150 ft The efficiency…

Q: ii. Water is rotated in a pump impeller at a speed of 1500 rpm. The inlet and outlet diameters are…

A:

Q: slug ) flows through the pipe system below. Data is given below: ft³ Pipe 1: V₁=1.8 ft, D₁=2.4…

A:

Q: Q4) A reservoir-pipe system given in the figure below. The air pressure in the tank is 25 N/em?.…

A:

Q: to the atmosphere. Estimate the pump power in kW delivered to the water.

A:

Q: In Fig. P3.130 the fl uid is gasoline at 20 ° C at a weight fl owof 120 N/s. Assuming no losses,…

A: Given data To determine the gauge pressure at section 1-1

Q: In Fig. P3.55 the jet strikes a vane that moves to the right atconstant velocity V c on a…

A: Part A). Let CV cover the vane and the cart and move to the right at the given cart speed. The jet…

Q: Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the…

A:

Q: Fluid at 20°C (7 = 9.789 kN/m², vapor pressure = 2.420 kPa (abs) flows in a series pipeline system…

A:

Q: 4 m of water, and each of the three elbows ha uces the diameter by a factor of 0.60 (60% o ntraction…

A: Given Data The pipe diameter after the pump is:Dafter=1.8 cm The pipe diameter before the pump…

Q: A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameter…

A: According to the continuity equation, the product of fluid velocity and cross-section area of the…

Q: A Closed tank of water with Length, I = 20 ft Height, h = 10.45 ft %3D Width, w = 5.6 ft %3D Pgage =…

A: Given: Length of the tank→L=20 ft Height of the tank→h=10.45 ft Width of the tank→w=5.6 ft Because x…

Q: 5-The crate has a mass of 80 kg and is being towed by a chain which is always directed at 20° from…

A: m=80kg; θ=20°; t=2s; μs=0.4; μk=0.3;

Q: B: The pump in Fig. Q3B increases the pressure in the water from 200 to 4000 kPa with a flow rate of…

A: To Find : The mechanical efficiency of the pump and overall efficiency pump/motor.Given : The…

Q: P3.114 Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate, as…

A:

Q: Pump Pam = 100 kPa D= 3 cm The pump in Fig. P3.146 draws gasoline at 20°C from a reservoir. Pumps…

A:

Q: The liquid in Fig. P3.126 is kerosene at 20 ° C. Estimate thefl ow rate from the tank for ( a ) no…

A: According to given condition the liquid is kerosene so density of liquid ant 1 atm and 20oC is ρ=840…

Q: The insulated tank in Fig. P3.182 is to be fi lled from a highpressureair supply. Initial conditions…

A: The initial mass inside the system can be calculated as,

Q: Water fl ows steadily through the box in Fig. P3.63. Averagevelocity at all ports is 7 m/s. The…

A: Given Data: The velocity at port 1 is V1 = 7 m/s. The velocity at port 2 is V2 = 7 m/s. The…

Q: 3.69 Determine the flowrate through the pipe in Fig. P3.69. P = 900 kg/m³ Water 2.5 m T Figure P3.69…

A:

Q: The large turbine in Fig. P3.184 diverts the river flow undera dam as shown. System friction losses…

A: Given data

Q: siphon draws water fror nospheric pressure. Assur velocity at point P in the

A: introduction: we have to find out velocity at point P

Q: tank half full of water is accelerated to the right at 9.81 m/s^2. If the motion is laong the side…

A: Given:a=9.81 m/s2l=4 m

Q: A river discharges into a reservoir at a rate of 400,000 ft'/s (cts), and the outflow rate from the…

A:

Q: A horizontal - shaft centrifugal pump lifts water at 65°C. The suction nozzle is one meter below…

A:

Q: Torricelli’s idealization of effl ux from a hole in the side ofa tank is V = √2 gh, as shown in Fig.…

A:

Q: A piston compresses gas in a cylinder by moving at constantspeed V , as in Fig. P4.18. Let the gas…

A:

Q: For a tank, calculate the volumetric flow of water, which comes out through a pipe, the tank is…

A: Given: Height of the tank: →h=2 m Exit diameter of the pipe: →Dexit=0.05 m So the cross sectional…

Q: Twelve high-speed water jets strike shown in Fig. P4.135. Find the power output and the blade angles…

A: Given -

Q: Water at 20 ° C fl ows at 30 gal/min through the 0.75-indiameterdouble pipe bend of Fig. P3.154. The…

A: Given data: The flow rate water is Q = 30 gal/min. The diameter of the pipe is d = 0.75 in. The…

Q: D, -6 cm Three pipes steadily deliver water at 20°C to a large exit pipe in Fig. P3.8. The D;=5 cm…

A:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.