21. Giventhe cross section notes of an earthwork between station 10+ 100 to 10+200. Assume both stations to have thesame sideslope and width ofthe base, determine the side slope. 4.5 6.45 +2.3 0.00 +1.5 +1.0 A. 1:1 В. 1.25:1 С. 1.5:1 D. 2:1

21. Giventhe cross section notes of an earthwork between station 10+ 100 to 10+200. Assume both stations to have thesame sideslope and width ofthe base, determine the side slope. 4.5 6.45 +2.3 0.00 +1.5 +1.0 A. 1:1 В. 1.25:1 С. 1.5:1 D. 2:1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given the following traverse: Line Distance Bearing 1-2 38.00 N40-00W 2-3 40.00 S50-00W 3-4 40.00…

Q: A. A tachometric surveying was conducted to obtain some readings for inaccessible points, where it…

A: SInce you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Example-5. The ground levels of a proposed longitudinal road section of the consecu- tive points 30m…

Q: What is the slope of EH if distance between them 300m.and R.L of E-30.09and R.L of H=29.25 0.0025 O…

A: Distance between EH(L)=300m To find slope of EH

Q: • Calculation of horizontal distance between PQ A 0 = 0° 2.750 R.L of H.I. = 1852.425 C S 1.900…

A: Given data: H.I=1.475 m R L of P=1850.950 m Staff readings: st=2.750sm=1.900sb=1.050

Q: A series of perpendicular offsets were taken from a transit ine to a curved boundary ine. These…

A: To Find :- Area using trapezoidal rule. Given Offsets are 2m, 3.2m, 4m, 3.5m, 5m, 4.5m, 6m, 7m at an…

Q: 1. Determine the slope correction for steep slope and the horizontal distance AB if two lines AC and…

Q: A turning point along a profile level route measures 284.98 m beyond station 30+ 58.70. Determine…

Q: Prob.7. Perpendicular offsets at 50 m intervals to the hedge are 10.6, 15.4, 20.00, 15.00, 16.00,…

A: (i) It is required to determine the area using the average ordinate rule.…

Q: A level is set up and a reading of 2.195 m is taken on a bench mark the elevation of which is 89.54…

Q: What is the slope of EH if distance between them 300m.and R.L of E-30.09and R.L of H=29.25 0.0025 O…

Q: Given the cross-section notes of an earthwork betweèn station 10+100 to 10+200. Assume both stations…

A: Considering the following diagram:

Q: Draw the longitudinal section ( profile) of the leveling process if vou know that the elevation of…

A: Assumptions:(1)- Since No Specific angle/Bearing is Given , so we are Considering The Offset as a…

Q: What is the slope of EH if distance between them 300m.and R.L of * E=30.09and R.L of H=29.25 _0.0028…

A: Given, Distance between EH =300 mR.L of E=30.09R.L of H= 29.25

Q: Given: Sta. 12+00 Elev. 602.07; Sta. 12+50 Elev. 601.09, Sta. 13+00 Elev. 596.07; Sta. 13+50 Elev.…

A: Given, Station and elevation of various points To find : Slopes between different reference…

Q: For the given line with equation 2x – 3y = 12, the slope and the y-intercept is Slope: 3/2;…

A: Write the given equation in slope - intercept form That is y= mx+c Here m= slope c =…

Q: Draw the 1ft contour lines across the 2-lane road below (12ft wide in each direction). (a) has a 4%…

A: a) Longitudenal slope= 4%crown-6 inchb) Longitudenal slope= 6%cross slope=3%…

Q: Situation 1: The back and forward tangent of a parabolic and 3%, respectively. The station of their…

A: back and forward tangents = -5% and 3%Intersection station = 30+194mIntersection elevation =…

Q: piece of ground three straight sides AB, BC and CD; the fourth AD, is irregular. The dimensions are…

A: The boundary of the given plot ABCD has 3 straight sides and one irregular side.AB = 126m, BC =…

Q: Determine the slope at C.

A: GIVEN : P = 110.5 KN L = 6 m TO FIND : SLOPE AT C ( θc )

Q: A level is set up and a reading of 2.195 m is taken on a bench mark the elevation of which is 89.54…

Q: Towers A and B stand on a leyel ground. From the top of the tower A which is 30 m, high the angle of…

A: Given data- The given situation in the question is shown below- To find- The height of tower B.

Q: 1. PACING. In field party counted 43.50, 43.25 strides. Then 105.50, 106.00, 105.75, and 106.25…

A: Since you have posted multiple questions we will solve only the first question, kindly repost the…

Q: 1.Explain how you will set-out the following: i.Two corners of a rectangular building using two…

A: A building is set out in order to clearly define the outline of the excavation and the centre line…

Q: Degree of static indeterminacy

A: Given data : The value of number of member in truss=3 The value of number of joint in truss=4 The…

Q: e. Right 4.5 +1.0 Right 6.9 +2.6 side slope of both sections value of x at station 10+250 if it has…

A: solution of above problem is below:

Q: art 2. If a level is being used to determine the elevation of the unknown as shown from a known BM…

A: Auto Level: It is levelling device which consist of three prims ,middle ones is fitted with fine…

Q: 10.21 8.03 Area 2.21 Shear Diagram -5.79 -6.32 -9.97 -13.79 9.28 Tangent Line 7.42 Moment Diagram…

A: Slope of moment diagram i.e. dM/dx = shear force at that point . In the above case the slope of the…

Q: HI = 1.496 ELEVATION OF PT A: = 200 K= 99 HAIR READING VERT. STADIA DISTANCE STA. OCC| STA. OBS…

Q: A docs.google.com =6 To establish a new benchmark on point B using a levelling instrument. The work…

Q: RL2=152.5 Q4). The following staff readings in meter were obtained when leveling along the center…

Q: 13. Given the cross section notes of an earthwork between station 10 + 100 to 10 + 200. Assume both…

Q: 4. The slope distance (L1) measured between A and B is 28.533m. Determined the correction necessary…

A: Correction = True value - Measured value In given question , Horizontal equivalent = true value…

Q: From the given leveling notes, compute the elevation of BM2 ELEVATION OF BM1 IS EQUAL TO 149.20

A: Given:- Station BS HI FS Elevation BM1 0.57 TP1 1.15 2.93 TP2 0.65 2.70 TP3…

Q: sorry，what are these： Step 3 Slope deflection equation In section AB MAB= MFAB+22EIL2θA+θB-3δLMAB=…

Q: 0.9 (IFS) 1.7 (IFS) 3.43 TP1 2.77 (BS) (FS) 2.32 (BS) BM1 EL. 328.70m 2.2 (IFS) BM2 2.45 3.7 (FS)…

A: Given question belongs to levelling topic. Here the back sight , intermediate fore sight and…

Q: Given: 1 = 23° 18' D = 4° 00' P.I. 40+53.87 = Find R, T, and L, by the chord definition. and compute…

A: Answer We are given I =23o18' D = 4o00' PI = 40+53.87 Calculations shown in steps below

Q: 6. A loop traverse originated and ended at point A. The bearing of line AB is S 42°30' W. Points C,…

Q: Determine the distance of line DA and CD. Also determine the area of the closed traverse using DMD…

Q: Draw the 1ft contour lines across the 2-lane road with 12ft lanes and 5ft wide shoulders. The…

A: Longitudenal slope= 5%cross slope=3% accross pavement =3% accross…

Q: 7. Determine whether the planes are parallel, orthogonal, or neither. 4x - 20y – 4z = 8 3x - 15y –…

A: If theta = 00 or 180⁰ : planes are parallel theta = 90⁰ : planes are perpendicular

Q: 32. Compute for the area by using DMD and DPD method. LINE BEARING DISTANCE AB S 36°46'W 44.84 BC N…

A: To determine the area of traverse using DMD and DPD method. First step is to write the Latitude…

Q: in meter were obtain center line of natural ground of a road. The elevation of de Line RL 148.4 m…

A: Rise and Fall method is used to find the level at each station Here the Road level at station 0+00…

Q: What is the slope of EH if distance between them 350m.and R.L of E=30.09and R.L of * H=29.25 0.0025…

A: Given that: Distance between EH, L = 350m R.L of E = 30.09…

Q: H.W: From the base line AB, the linear measurements (offsets) are taken to setting out a rectangular…

A: Surveying is the branch of the construction industry in which the measurement between different…

Q: From the given data of a closed traversed, compute the following, Line Bearing Distance AB S.8deg.…

Concept explainers

Construction Surveys

A construction survey is a survey done on a construction site to mark construction activities and for laying out positions for construction equipment. It includes evaluating and estimating construction activities before the beginning of the project.

Question

21. Giventhe cross section notes of an earthwork between station 10+100 to 10+200. Assume both stations
to have thesame sideslope and width of the base, determine the side slope.
6.45
0.00
4.5
+2.3
+1.5
+1.0
A. 1:1
В. 1.25:1
С. 1.5:1
D. 2:1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

VIEW

Step 2 Answer

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Situation 1: Given the cross section of an stations earthwork between 10+100 to 10+200. Assume both stations to have the same side slope and width of base. 6.45 +2.3 6.0 +2.0 Sta. 10+100 0 +1.5 Sta. 10+200 0 X 4.5 +1.0 6.9 2.6 Find: a) The base and side slope of both sections. a cross b) The value of x at Sta. 10+200 if it has sectional area of 14.64 m². c) The volume between the two stations using the end area with method prismoidal orrection. F a i C M d e S S C S C
8. A civil Engineer proceeded to do the stadia survey work to determine the topography of a certain area. The transit was setup at a point A, with the line of sight horizontal, took rod readings from the rids placed at B and C which is 200 m and 60 m from A respectively. Compute the stadia interval factor. Stadia intercept at 8 = 2.001 m and the stadia intercept at C is 0.600 m. a. 100.00 -b. 101.28 C. 99.93 d. 110.17
A field is in the form of a regular pentagon. The direction of the bounding sides was surveyed with the assumed meridian 6° to the right of the true north and south meridian., the bearing of one side AB is N 40°57’ W. Compute the bearing of CD
Compute for the given closed traverse the following:a. Bearing of each lineb. Latitude and Departure of each line,c. Linear error of closured. Precision e. Adjust the traverse using the transit rule. If the coordinates of point B are Northing =3000.00 m. and EASTING = 1500.00 m., determine the coordinates of all other points. LINE INTERIOR ANGLE LENGTH (m.) BEARING A-B A = 125 deg 54 min 162.60 N 28o 17’ E B-C B = 135 deg 00 min 253.98 C-D C = 114 deg 27 min 256.32 D-E D = 121 deg 52 min 305.94 E-F E = 88 deg 59 min 335.40 F-A F =133 deg 48 min 182.04
From the base line AB, the linear measurements (offsets) are taken to setting out a rectangular fence CDEF, find CD”, DE~ knowing that AB~ = 170° 5.
Single proportionate measurement usually requires four original corners, and the location of the propertined corners is positioned at the proportionate distances of lines run from the propoertied points. a.) True b.) False
the traverse is divided by a line passing through d and b. the bearing of the dividing line db is . what is the length of the dividing line db?the traverse is divided by a line passing through d and b. the bearing of the dividing line db is n85° 20'e. what is the length of the dividing line db?
Points A and B are 100 m. apart horizontally and are of the same elevation as the foot of a building. The angles of elevation of the top of the building from A and B are 21 and 32 respectively. How far is A fro the building? a) 259.28 m b) 235.56 m c) 243.34 m d) 274.36 m
Elem. Surveying
comp ters o sic The level 1851 ave m, 19. The line of sight was inclined at 4°30' from the horizontal and intercepted the stadia rod with the length of 1.8 m. the stadia interval factor is 100 and stadia constant is 0.3. Compute the vertical distance of the point sighted above the instrument. on bounded by the curve
Layout by coordinates method: Given are the coordinates of two points P1 and P2. It is required to layout point P2 from an instrument set up at Point P1. P1 P2 Northings (m) Eastings (m) 456.34 567.45 398.12 485.70 6. Determine the bearing to layout point P2. a) S 60°55' W b) N 60°36' W 7. Compute the distance to layout point P2. a) 140.45m b) 100.36m c) N 70°10' W c) 129.90m d) S 54°33' W d) 110.30m
Q5) A road at a constant R.L of 180.00m runs North to South. The ground East to West is level. The surface levels along the center line of the road are as follows: Changing in meter: 0 30 60 90 120 150 180 Level in meter: 183.50, 182.45, 182.15, 181.55, 180.95, 182.05, 180.80 Compute the volume of cutting by both the trapezoidal and prismoidal formulas, given that the width at formation level is 8m and the side slopes is 1 to 1.