2021-03-16 Q13. A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, 200 GPa, as = 11.7 x 10/°C) and portion BC is made of brass (E, = 105 GPa, a, = - 6/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C. 20.9 x 10

2021-03-16 Q13. A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, 200 GPa, as = 11.7 x 10/°C) and portion BC is made of brass (E, = 105 GPa, a, = - 6/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C. 20.9 x 10

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
Aluminum Bronze Steel 2P 3P P 4P - - 1.0 m 0.8 m FIG. P2.16 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses pre- scribed in the table are not to be exceeded. A (mm²) E (GPa) G, (MPa) Вronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140
The steel bars are firmly attached to rigid supports. Initially the temperature is 840F. Determine the stress in bars AC and CB when the temperature becomes -600F. Use E = 29 x 106 psi and α = 6.50 x 10-6/ 0F.
For the shown Fig., find the maximum shearing stress in bronze part of the shaft. * Steel d= 200mm G= 80GPa Bronze d= 100mm d= 100mm G= 40GPa G= 30GPA 2KN.m Aluminum 8KN.m 3kN.m 3m 2m 1.5m +
3.2 The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises by 20∘C after a load W = 110 kN is applied.
Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 125°C. The 0.5-mm gap exists at 20°C. q = 5 t = 0
When the temperature is at 30°C, the steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T = (3x² 20x + 120)°C. Calculate the normal stress developed in the pipe. Assume each tank provides a rigid support at A and B. a=12X10-6/°C - 150 mm 10 mm- Section a - a -6 m a a B
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d, = 1.5 in.; both have length L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P