200V d.c shunt moter takes 4A atno- Load when runing ab 700 r.p.m. The FieldYesistance is 10002.The resistance of the armatureat stand stillgives adrop of 6 Volt a cross armatureterminals when 1o A were pass ed through itCalculate (i) the spesdon load(11) the armaturečif) efficiency.The pormal imput of motor is 8 kwatorqueQ2:A 4-pole ,250V series motor has a waveConnected anmature with 1254 Cenductors. TheFlux per pole is 22 m wb wwhen the motorristaking 50A. Iron and fricion losses amount to1kw. Amature resistance is o-202 and seriesfreld resistance is oo202 Calculate :-(i) the speedC) the shaft torque(ii) the efficiencyl

According to our rules , we will answer only the first part of the question .If you want solution…

200 V d.c shunt motertakes 4A at no - Load when runing ab 7F00 V-p.m. The Field Yesistance is 10002.The resistance of the armature at stand still gives adrep of G Volt a crass almature terminals when toA were pass ed through it Calculate (i) ihe sperd, on load (if) the armature Čii) efficiency torque

200 V d.c shunt motertakes 4A at no - Load when runing ab 7F00 V-p.m. The Field Yesistance is 10002.The resistance of the armature at stand still gives adrep of G Volt a crass almature terminals when toA were pass ed through it Calculate (i) ihe sperd, on load (if) the armature Čii) efficiency torque

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the use of prime mover?
A 4 pole lap wound dc machine has 728 active conductors running at 1800 rpm. The flux per pole is 30mWb, The armature current is 120 A, What is the electromagnetic power developed in the armature?
Q1/A) Fill in the following blanks 1. The air gap between stator and rotor is about...mm 2. The iron losses are depending on ..4sker,.ddcam 3. The relationship between stator and rotor current frequency is ....... 4. The range of operation mode slip is ...... 5. The relationship between hysteresis loss and frequency is .... 22 1-V T
Two de generators each having linear characteristics that operate in parallel. One machine has a terminal voltage of 480V at no load and 220 V at a load current of 100A, while the other machine has a voltage of 470 V at no load and 200 V at 120 A. calculate the current in each generator and the bus bar voltage when the total load is 180 A. What is the kilowatt output of each machine under this condition?
Colve asap
Do you What is Induction motor?
14-
Is this armature winding a progressive or a retro-progressive winding? W N Select one: 2 B 4' O a. Both O b. Progressive OC. Neither O d. Retro-progressive B S
A de machine is controlled by the step-down de-de converter shown below. The armature inductance La =0.2 mH and the armature resistance can be neglected. The armature current is 5A. The Buck converter is operating at the switching frequency is 30 kHz and the duty ratio is 0.8. L₁ + Answer the following questions: 1) Calculate the input voltage (Va) if the output voltage (ea = 200 V). 2) Find the ripple in the armature current (a). 3) Calculate the maximum and minimum values of the armature current (la). 4) Sketch the armature current (ia (t)) and the supply current (id (t)).
13/ Desc ribe The principle os operation and brief constru ctional de ta ils of a DC machine.
What is the commutator pitch of a 4-pole, duplex wave-wound armature having 120 commutator bars?