A dc shunt moton runs at looo Y.P.m From 500V SUPPIY whentaking an armatuie currant of 95 A . caleulat e the spees at whichitwill Ynn ffom 9250v supPly when taking an armature eurrent of 50A.the resis tance of the armature circuit o. .ssume the flud Per Poleat 250V to have decreased to 70%% of its Value qt 500 V ·

The given data's are, The speed N1=1000 rpm, The voltage V1=500 V, V2=250 V, The armature current…

A de shunt moton Yuns at lo0o Y.P.m From q 5 00 V SUPPIY when taking an armature currant of 5 A. calculate the SPeed at which itwill Ynn from a250V supPIy when taking an armature ewrrent of 50A. the resistance of the armature circuit o. .A5Sume the flud Per Pole at 250V to have decreased to 70% of its Value at 500V.

A de shunt moton Yuns at lo0o Y.P.m From q 5 00 V SUPPIY when taking an armature currant of 5 A. calculate the SPeed at which itwill Ynn from a250V supPIy when taking an armature ewrrent of 50A. the resistance of the armature circuit o. .A5Sume the flud Per Pole at 250V to have decreased to 70% of its Value at 500V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

QUESTION 3 is dc -Lac 0 f(t) = Ide T If ripple-free load current in steady-state is assumed, the input current is waveform of the single-phase full-wave rectifier may then be depicted as shown in the figure above for an ideal input transformer. With the assumption that the supply is ideal and perfectly smooth and ripple free load current, which implies an infinitely large load inductance, it is quite straightforward to obtain an analytical expression for the input current harmonics. The rectangular wave is defined as de 270 when 0< t < π when_π
Q1: Write the name of this Circuit L(consta ww R, R Flux from servoamplifier LOAD
I need the answer as soon as possible
Relationship of the two - direct relationship, inverse relationship, no effect Atomic Packing Factor – Slip Process Elastic Modulus – Bond Strength Temperature (Superconductor) – Diamagnetism Vacancies of Si – Charge carriers Stress Amplitude – Fatigue Life
For the circuit in the figure below, the supply is 220 Vms, 60 Hz. The load resistance is 16 N. Neglect the Vr of the SCR. a) How much power is delivered to the load if the firing delay angle= 0°? b) How much power is delivered to the load if the firing delay angle= 90°? c) If the firing delay angle= 135°, will the load power be less than one-half or more than one-half of the amount delivered for a 90° delay angle? Explain. RLoad R1 R2 Vsupply SCR
20. The output of a single phase mid-point rectifier is 20 A, 150 V dc while the input supply voltage is 220 V AC (rms). Find the transformer rating, voltage ratio and transformer primary current. Assume the firing angle to be 30° and the load to be inductive. [Hint. Ref. Ex 4.8] 21. A single phase full controlled bridge is fed from 220 V ac rms supply. The load current for the RL load resistance is 8A and the firing angle is 60°. Calculate the active and reactive inputs. If one of thyristors gets open circuited obtain the aver- age dc output voltage and current for same firing angle. How can you ensure that the load current be continuous ? [Hint. Ref. Ex 4.15] 22. A single phase half wave rectifier alongwith a commutating diode is used to supply a heavily inductive load from a 250 V ac supply. Assuming the load cur- rent to be 15 A, find the average load voltage for a=45°. What is the load resis- tance ? If the firing angle is made 100°, does the load voltage become negative ? [Hint.…
What do you mean by Ferranti effect? How does it affect voltage regulation? Which one among efficiency and voltage regulation can be negative? Give reasons?
DA shunt generator is used to charge a battery of 100 cells in series. If each cell has a terminal p.d. of 2.5V at the completion of charge and is of internal resistance 0.001 Q calcu- Cate the e.m.f. to be generated to give a charging current of 15A at the end of charge. Assume that the armature and field resistances are 0.2 2 and 200 2 respectively and the cables onnecting the generator to the battery have a resistance of 0.6 Q.
Materials in parallel, supplying a load of 500 amps, with a terminal voltage of 240 volts, and the resistance of the product circuit 0.04 Ohm The resistance of the field circuit is 60 ohms. Calculate a. Product current b. field current c. electromotive force
(B)-Explain by drawing the change in the direction of current flows through coils at the ideal case of commutation by considering coil B which is the coil under commutation as shown in the figure below. B C 5A SA 5A Armature winding 10 A Commutator 10 A Brush
Aa - AaBbCcl AaBbCcl AaBbC 1. Av 1 Normal 1 No Spac. Title Editing Dictate Sensitivity Editor Reuse Pick Files Imag Paragraph Styles Voice Sensitivity Editor Reuse Files Picki 5. A PMMC voltmeter with a resistance of 10 ohms gives has a coil of effective depth of 3 mm and a width of 2.5 cm, the coil has about 100 turns. The flux spread in the air gap is of 10mWb/m. The spring has a constant of 2 x 10 Then calculate, Deflection torque produced by the coil, when it is connected to 20V to measure. ii. Deflection made by the pointer, when the meter is to measure a voltage of 10V i. ed States) DFocus
Q15/ Complete the blank Electron gun has a.................................................... for varying the electron density.