200 mm 300 mm -600 mm- IB 200 mm 30 Prob. R8–3

Q: The coefficient of static friction for both wedge surfaces is 0.48 and that between the 37-kg…

A: Given  μs=0.48m=37 kgμ=0.60 To find P

Q: The 35-kg homogeneous smooth sphere rests on the 24° incline A and bears against the smooth vertical…

A:

Q: Q1/ 30 MМ 60 MM IF : N.A |= 27 * 10° mm 120 MM V= 19.5 KN Determine the maximum and minimum shearing…

A: Given- MOI (I)= 27× 106 mm4Shear force( V)=19.5KN

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

A:

Q: 1. Find the force necessary to move the big block uphill. 1000 kg F H= 0.1 10°

A: Given Data: The mass of the block is m=1000 kg The weight of the block mg= 1000×9.81 = 9810 N The…

Q: 3. Determine the reaction of supports using slope deflection method. El is constant. 20 kN / m 24 kN…

A:

Q: 3. Determine the internal normal force, shear force, and bending moment at point B.

A: Consider section as shown :

Q: 3.) An isosceles triangle is submerged vertically in water with its 5.4m base at a distance of 1.8m…

A:

Q: PROBLEM NO. 3 A uniform bar AB is resting in a horizontal position on smooth inclines as shown…

A:

Q: Determine the force (N) in link AB if P = 41.8 kNand d = 0.37. Round off only on the final answer…

A:

Q: A block is resting on a 30° inclined plane with a µ = 0.3. Find the required force P acting…

A: Let us estimate the force P in step 2.

Q: A solid circular pole is subjected to linearly varying distributed force with maximum intensity ao…

A: Moment at base is given by ; M = (12 X L X qo) X (L3) M = (12 X 8 X 5.7 X 103) X (83) M = 60800 N-m

Q: Problem 1. Determine the minimum horizontal force P required to keep the crate from sliding down the…

A: Given:- The mass of the crate = 50 kg The coefficient of friction between the crate and the incline…

Q: In your own words, explain what is meant by work.

A: Work is measurement of energy that is transferred when an body moves over a given length by an…

Q: A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1…

A:

Q: fl m→ -2.0 m- e total deflection at B. [Hint: Use

A: a)   Take , a = 1m from left  , x = 2m from left , l = total length = 4m Given : EI = 2000 KNm2…

Q: For the beam in the figure; a) Find the coordinates of the geometric center and the moments of…

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Ax=0

Q: A horizontal force P = 69,651 N is pushing an inverted L-frame supported by a foundation at the…

A:

Q: The coefficient of static friction for both wedge surfaces is 0.41 and that between the 31-kg…

A:

Q: #2. Determine the horizontal displacement at point A. E = 200,000 MPa, a cross-sectional area = 600…

A: Step 1:Step 2:Step 3:  Hope this helps!

Q: For the simply supported beam carrying the concentrated load P = 223 N at its midspan, determine the…

A:

Q: A cylindrical caisson having an outside diameter of 7m floats in sea water sg=1.03 with its axis…

A: Given, Outer diameter of caisson (D) = 7m Specific gravity of sea water= 1.03 h= 6m Our aim is to…

Q: 1. Determine the shortening of bar BE. 2. Determine the vertical displacement of point A. 3.…

A: Consider the free body diagram of the given beam supported by rigid bars as shown below. Assume A…

Q: Using the SLOPE-DEFLECTION. Solve for the support reactions.

A: Reaction calculation using slope deflection method

Q: A horizontal plate turns an oil jet. If ?1 = 30 m/s, ?2 = 25m/s, and the area of incoming jet ?1 =…

A:

Q: I. Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I=70(10%)mm*. Use…

A:

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

A:

Q: Determine the resultant of B and C if the resultant of A and B is 100 kN directed along the z-axis.…

A:

Q: compute the value of P and .

A: Given Data Sphere Weight, W=300 kN Weight passing Over, W1=200 kN Pulley is frictionless Angles,…

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

A:

Q: The vertical bars AB and CD have a shear modulus G = 3.7 x 106 .Determine: the maximum shear stress…

A:

Q: CLO 1: Determine the maximum bearing stress in MPa if P = 115 kN.

A: Force is the quantity of loading that occurs on the system. The direction o forces can be upward,…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.