A horizontal plate turns an oil jet. If ?1 = 30 m/s, ?2 = 25m/s, and the area of incoming jet ?1 = 0.06 m2. Determine the required force in the x-direction to hold the plate

Q: Water flows through a horizontal bend in the (x, y)-plane and discharges into the atmosphere as a…

A: A pipe section is given with a horizontal bend of  and discharges into the atmosphere.Discharge, The…

Q: Q3/ The beam is subjected to a moment of 15 kip.ft. Determine the resultant force of the bending…

A: Given: The I section as shown

Q: 4. Four identical wires support a rigid bar as shown. If stress is not to exceed 150 N/mm², find the…

A: All the wires are identical so the diameter will be the same for all. The load at wire C is 40 kN.…

Q: 2. The block of weight W2 is being held in its position by two cylindrical rollers resting on…

A: For maximum value of W2 block should be in equilibrium.

Q: The yacal beam with 5000 lbs weight is carrying two vertical loads. The beam is supported by a cable…

A:

Q: A solid shaft has a circular cross section of diameter 150 mm and is required to transmit power at…

A: Given data : Diameter of shaft (d)=150 mm Angular speed n=9060 rps Maximum shear stress ζMax=85…

Q: Determine the force P required to force the 16° wedge under the 97-kg uniform crate which rests…

A:

Q: FRICTION In the beam system shown in the figure, the 200-KN Block is supported by a rod (Rod C),…

A:

Q: Determine the horizontal force P that would keep the uniform 12-kg rectangular plate in the position…

A:

Q: ermine the mi im diameter of å söli- ne yield stress of the material of the ba - 119.2 mm.

A:

Q: SITUATION 32 The simply supported beam in the figure below has a rectangular cross section 120 mm…

A: To find the Bending stresses

Q: 1. A barrel in the form of a frustum of a cone with a radius of 3m at the bottom and 6m at the top.…

A: Density of oil = 0.85*1000 = 850kg/m3

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: What is the vertical reaction at support D? 50 kN 15 kN/m 150 kN · m A D В C 6 m 3 m -3 m

A: At equilibrium, the sum of vertical force acting on the beam is equal to zero. VA+VD = 15×6+50…

Q: www 12N sie TE Ar0.6 m

A: Given- weight of slider = 6 kg

Q: the block of weight W2 is being held in its position by two cylindrical rollers resting on inclined…

A: Given Coefficient of static friction between all surfaces is 0.36 Weight of cylinder W1 = 437 kN

Q: QI The built-up beam is formed by Welding together the thin plates of thickness 5mm. Determine the…

A: The shear centre  lies on the axis of symmetry and divides the distance between the C.G's of…

Q: The block of weight W2 is being held in its position by two cylindrical rollers resting on inclined…

A: Given, Wight of the cylinders (W1) = 400 kN Coefficient of static friction (μs) = 0.36 We are to…

Q: What is the vertical reaction at support A? 50 kN 15 kN/m 150 kN · m A D В 6 m 3 m 3 m

A: As the given beam is in equilibrium we can calculate the support reactions by using the 3…

Q: Determine the change in length, breathand thickness f Ex a steel bar which is 4 m long jomm wide and…

A: It is required to determine the change in length of steel bar. δl=PLAE Here P is the applied load, L…

Q: A block of wood having a volume of 0.034 m and weighing 300 N is suspended in water as shown, a…

A:

Q: The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D…

A:

Q: 1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at…

A:

Q: D (5000 mm2) (4000 mm) E (5000 mm) 3 m 4000 mm) (S000 mm?) B (5000 mm?) A 100 kN 2 panels at 4 m 8 m…

A:

Q: ) If the beam is subjected to a bending moment of M = 50 kN.m, determine the bending stress at…

A:

Q: The masses of the frictionless cylinders A and B in FIG JWU are 2.0 kg and 1.0 kg, respectively. The…

A:

Q: 0.2: Consider the cantilever beam subjected to the concentrated load shown below The cross section…

A:

Q: 6-50 The beam is subjected to a moment of M = 40 kN. m. Determine the bending stress acting at…

A: ANSWER :​​

Q: The beam AB shown in the figure supports a uniform load of intensity 3000 N/m acting all over half…

A:

Q: PROBLEM 12.70 Pin B weighs 4 oz and is free to slide in a horizontal plane along the rotating arm 0C…

A: To find radial and transverse component of reaction at B and value of P and Q

Q: What should be the magnitude of 500 the P in order to make the force in F FE as compression. 2m 500N…

A: Finding out the magnitude of the P in order to make the force in FE as compressive.

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.