-200 mm 200 mm A 125 mm

Q: Two blocks are connected by a ngid strut (with negligible weight) attached to each block with…

A: FBD is drawn for both the masses A & B. fs=μN Answer: WA = 736.98 kN

Q: The brake is to be designed to be self locking, that is, it will not rotate when no load P is…

A:

Q: A uniform rigid bar which weighs 1000KN/m is supported by a cable at point B, a rough surface…

A: Given data, Intensity of the weight of the bar, w = 1000 kN/m Coefficient of static friction for all…

Q: Determine the force P required to move the wedge to the right if the coefficient of static friction…

A:

Q: Due to the force of magnitude magnitude 100N applied on the jockey pulley, the top of the slack side…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is…

A: Given:Force acting on one end, F=30 kNWeight supported by the forec, W=30,000 kN

Q: If P = 290 N, determine the required minimum compression in the spring so that the wedge will not…

A: Write the given data with the suitable variables. μ=0.35P=290 Nk=15 kN/m   It is required to…

Q: The box shown in the figure has a weight of 250 pounds. The coefficient of static friction between…

A:

Q: Determine the angle of contact () in degrees of the belt supported on a pulley if the belt is having…

A:

Q: * 1. The light bar is used to support the m kg block in its vertical guides. If the coefficient of…

A: (a) Draw the free-body diagram of the block. Apply force equilibrium in vertical direction.…

Q: Please solve the question in handwriting step by step

A:

Q: Determine the maximum angle a with the vertical that the ladder can make without falling on the…

A: L = length of the wall

Q: Q2/ Arm ABC acts as a brake on the wheel as shown in Fig. 2. The coefficient of static friction at B…

A:

Q: Determine the smallest force the man must exert on the rope in order to move the (160 )kg crate…

A:

Q: In (Figure 1), the man has a mass of 75 kg and the crate has a mass of 130 kg. The coefficient of…

A:

Q: Help!!! Answer it Correctly!!! Please

A: 1. Determine the forces acting on Block A:Weight of Block A (WA​) = mA​⋅g where…

Q: Blocks A and B weigh 250N and150N, respectively. Using the coefficients of static friction indicated…

A: Weight of block A = 250N Weight of block B = 150N Weight of block E = W To find: FBD of pulley C,D…

Q: Two hemispheres having an inner radius of 2 ft and wall thickness of 0.25 in. are fitted together,…

A: Given data: The inner radius of hemisphere is R = 2 ft. The wall thickness is t = 0.25 in. The…

Q: The three flat blocks are positioned on the 30° incline as shown in figure, and a force P parallel…

A: The normal force (N) is the force exerted by a surface that supports the weight of an object resting…

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Free-body diagram of the handle is given as,   On using equilibrium of moment about A is written…

Q: Determine the minimum coefficient of static

A: Given Data The mass of the car m= 1400 kg=1400*9.81=13734NFind Outa) The minimum coefficient of…

Q: 5 ft B N 1.5 f

A: given-         uniform concrete block in (Figure 1) has a weight of 300 lb. The coefficients of…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: the bolt is

A:

Q: The three bars have a weight of WA = 20 lb, WB = 40 lb, and W. = 60 lb, respectively. If the…

A:

Q: Two blocks A and B shown in (Figure 1) have a weight of 9 lb and 6 lb , respectively. They are…

A: Given data is

Q: The mine car and its contents shown in (Figure 1) have a total mass of 4.5 Mg and a center of…

A:

Q: Two blocks A and B shown in (Figure 1) have a weight of 11 lb and 6 lb, respectively. They are…

A:

Q: We are experimenting with a brake system. Bar AC rests on the spool at B. Find the force P that can…

A: Consider free body diagrams of bar AC and spool at B.

Q: In the figure, a climber with a weight of 390 N is held by a belay rope connected to her climbing…

A: Given Data The weight of the climber is: w=390 N The angle at the toe is: θ=45° The angle at the…

Q: Can the system in given figure be n static equilibrium in the position hown? The uniform bar AB…

A:

Q: A square threaded screw is used to clamp two boards together. The clamping force on the boards is…

A:

Q: + High-strength bolts are used in the construction of many steel structures. For a given bolt, the…

A: To determine:Required couple(M)

Q: Problem -02 Dry FrictionKnowing that a couple of magnitude 30 N m is required to start the vertical…

A:

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given, Coefficient of friction, μ=0.15 Weight of the handle, W=15 N Applied force to the end of the…

Q: Couple forces of F= 35N are applied to the handle of the machinist's vise. The guid at B is smooth.…

A: Given-To Find-Compressive load on block P=?

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: First, draw the free-body diagram of the handle: Now write the moment equation about the point 'O'…

Q: The uniform concrete block in (Figure 1) has a weight of 300 lb. The coefficients of static friction…

A:

Q: In the vise shown in the figure, the screw is single-threaded in the upper member: It passes through…

A: Step 1:Given data:In the vise shown in the figure, the screw is single-threaded in the upper member,…

Q: The block as shown in Figure 3.6 has a weight of 250 N, which is inclined at 30° to the horizontal.…

A: Below is the solution of the question mentioned

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.