20. What are the cross sectional area, leg dimensions and thickness of an L6x4x1/2? (Hint: Use your AISC Manual.)

Q: The bolted connection shown is to be used to transmit a tension of 175 kips by using 7/8” A325 bolts…

A: The given data is shown below: Load=175 kipsDiameter of bolts=78 in.Width of outer plate=8 in.Width…

Q: Problem 2: A existing (E) W18x40 is deflecting too much and you were asked to decrease the floor…

A: Given data,section (E)W18x 40space is limiteduse maximum 3" deep memberFindchoose the WT member to…

Q: A channel shown is attached to a 12 mm gusset plate with 9-22 mm diameter A 325 bolts as shown. Use…

A: 12 mm thick gusset plateTo determine:the capacity of the channel based on the bearing strength of…

Q: A column bears the loads as shown in the table below. Calculate the design load for both ASD and…

A: From the given data, we have to find out design load for both ASD and LRFD methods. Load type…

Q: What is the net effective area for the angle section as shown in figure? The angles are connected…

A: For given angle,Connected using M18 bolts of grade 4.6To find net effective area for the angle…

Q: 3x Jim (1-e y4 Xー0

A: solution  to find the limit of this problem  use the L- Hospital's rule  as the limit is in 0/0 form…

Q: Determine the number of plywood and 2x2 wood frame for the outdoor pad shown on the plan.Use Class A…

A: A layout of a building is shown in the figureC1 dimension = B1 dimension = CB1 dimension =

Q: The connection shows a PL10X200 loaded in tension and welded to a 10mm gusset plate. Calculate the…

A:

Q: Questions Determine the net critical width of the bolted connection shown. Plate thickness is 25mm…

A:

Q: 16. What are the actual depth and flange width of an HP12×84? What are the thicknesses of the web…

A: Objective: To determine the actual depth, flange width, and the thickness of the flange and web for…

Q: Using Table A-5, determine the specific modulus in units of inches for AISI 1015 hot-rolled steel,…

A: Physical constants of the materials are given asModulus of elasticity of AISI 1015 hot rolled steel,…

Q: A vertically-held sledge hammer is easier to balance when the heavier end is Group of answer choices…

A: Sledge :- The sledge is a land vehicle that slides across a surface. It is built with either a…

Q: bolts evenly spaced around a bolt circle 12 in. in diameter, and six 4 -in. aluminum bolts on a…

A: To find the torque (T)-

Q: Determine the Allowable Axial Tensile Strength (Tensile Capacity) of L3x3x3/8 (A36 Steel) with four…

A:

Q: | 5% in = 12 ft 8 in 5 in (a) 4-PL3/8 X 5 Fy-36 ksi

A: Given data: Section- PL38x5 Effective length, Le=12 ft 8 in The design strength can be calculated…

Q: 7. What is the value of G for a three- piece 45° angle iron bracket if the thickness of the metal is…

A: Given :A three- piece 45 degree angled iron bracket The thickness of the metal is 1/4 inch andthe…

Q: Multiple Choice O о O 1.03 cm 1.79 cm 2.13 cm 3.72 cm

A:

Q: An L4 x 4 x 7/16 tension member is connected with 3/4 –inch-diameter bolts, as shown in the figure.…

A: Given: The angle used is L 4×4×716 . The diameter of the bolts is equal to 0.75 inches. Here grade…

Q: Grade: 10.9 Included I Grade: S235 ace Class: C atio of the mean installed bolt pretension to the…

A:

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.