20 Vrms source supplies a parallel RLC circuit with the following values: R=100 ohms, XL=200 ohms and XC=300 ohms, find: 1- Magnitude of the apparent supplied power to the circuit = VA. 2- The power supplied power factor value = %. 3- The supplied current is lagging or leading the supplied voltage = Note: Round your answers to two decimal places.

20 Vrms source supplies a parallel RLC circuit with the following values: R=100 ohms, XL=200 ohms and XC=300 ohms, find: 1- Magnitude of the apparent supplied power to the circuit = VA. 2- The power supplied power factor value = %. 3- The supplied current is lagging or leading the supplied voltage = Note: Round your answers to two decimal places.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit given in the figure VT = 25mV, | VBE | = 0.7V, R1 = 950.31Kohm, R2 = 22.50Kohm, R3 = 2.51Kohm, R4 = 1.08Kohm, VCC = 13.00V, VEE = 3.00V, VA = 13.08V, Beta Since = 193.00, Rs = 22.94ohm, Ry = 14.49Kohm, calculate the IC current, Ri, R0 and the voltage gain according to the Source (V0 / V1) by making full analysis. When making your transactions, 2 steps will be taken after the point. Select the closest option according to +/- 10% margin of error. There is only one correct answer to the question.
Q2: Tow anti parallel thyristors (Triac) supply a load resistive load with R=10 Q from a source with sinusoidal Waveform of peak value of 300V. a) Determine the output voltage if the firing angle a = 30°, a = 90°, a = 120° and discus results of (a) by your own words. b) Source power factor for each value of a in (a). c) RMS current of one SCR if a = 30°. %3D
The effect/effects of increasing the damping ratio 5 of a second-order system is/are O a. The maximum overshoot decreases and the damped frequency decreases O b. The settling time decreases and the peak time increases O c. The maximum overshoot increases and the damped frequency decreases O d. The settling time decreases and the peak time decreases
In the circuit given in the figure, Rk = 7.34Kohm, R1 = 1487.50Kohm, R2 = 1845.84Kohm, R3 = 1.61Kohm, R4 = 0.54Kohm, R5 = 19.05ohm, Ry = 91.57Kohm, VCC = 10.00V, VTN = 2.85V, Kn = Since it is 2.44(mA/V^2), C1=10.04uF, C2=13.81uF, C3=14.07UF, calculate the lower cutoff frequency of the circuit in Hz. When making your transactions, 2 digits will be taken after the dot. Write your result in Hz according to + 10% margin of error. While writing the answer, values such as spaces (Hz, KHz) etc. should not be written in front of the value and behind it. Only numeric values should be entered. A period (.) should be used as a decimal separator. An example notation is given below. Let the value you find be 1.15K. You should write 1150.00 in the box. Let the value you find be 432.6. You should write 432.63 in the box. If the correct answer is X, values entered in the range of X ± (X*10/100) (including limits) will be accepted. If x=50, it will be accepted as between [45,55]. VCc R1 R3 C3 VO Q1 Ry…
Am i right if not what is my mistake Q11
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
Question- A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A. If the solar cell resistance is 0.5 Q, then find the period for which each thyristor be reverse based.
Please i need the answer for this electrical experiment with the diagram and schedules thanks
Short Problem: Given a parallel RLC circuit comprised of the following element: 63.27-ohm resistor, ideal inductor with reactance of 63.75 ohms; and a capacitor with reactance of 6.25 ohms. Compute for reactive power in VArs given an ac voltage source of 100 cis 0 volts. Give only the absolute value. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.
1- Effective value when connected in series with a pure resistor R with resistance r and inductance L With the application of 100V sinusoidal voltage, three classes of current are 5A. The voltage across the coil and resistor element is 80V and 30V. a-Find the power and power consumed by the coil alone? b- Find the power consumed by the system and the power factor? c- Draw the voltage triangle, impedance triangle and power triangle? 2- 2- Voltage applied to a system composed of two pure elements connected in parallel. U = 141.1 sin (6280t-40) and I = 28.28 sin (6280t + 20). a- Find these two element values? b- Find the power spent in the system? 3-3-i1 = 100sin (750t + 45) i2 = 50sin (500t-30) U = 200sin (750t-90) Plot three graphs of current and voltage with equations as above. (n = 3 to be taken, frequencies will be found)