= 20 mm m₁ = 476 Wdg/m n₂ = 300 Wdg f = 10.7 kHz = 10.7 x 10³ Hz Ho,theoretical = 4 x 10-7 N/A² 1.26 x 10-6 N/A² • Calculate the cross-sectional area of the induction coil: A = nr² = π (2 × 10-³) ² = • Write down the slope of the line: slope = [] = 3.81 • Using the relation emƒ = µ₁Аn₁n₂(2ƒ)I, calculate the experimental value for vacuum permeability: slope Ho,experimental An₂n₂ (2πf) • Calculate the error percentage: error % = Ho.theoretical Ho.experimentai Ho theoretical -x 100% =

Q: we place the ring from part a in a time-varying magnetic field given by   B = B0 (1 − t/T)  0 < t…

A:

Q: 2) Voltage Phasors I Suppose you have a circuit that adds together two time-varying voltage inputs,…

A: Given: Input voltage,V1(t)=V1sin(ωdt+ϕ1)                ⋯1 Input voltage,V2(t)=V2sin(ωdt+ϕ2)…

Q: 2-1 Determine Zrexpressed in phasor form. R L = 0.3 H v = 240 sin(120 n t) (AC C- 40 μ R = 22 Q 2-2…

A: In the given question, We have to determine the value of ZT in part(a)  and current through the…

Q: 14) Two coils of wire are located near one another. Both coils have a circumference of 4 cm, and…

A:

Q: a] Faraday's law of induction states that the emf induced in a loop is directly proportional to the…

A:

Q: 1. For a long solenoid, we discovered in a problem-of-the-day that B = µ,nl, where n is the number…

A: (a)Consider l be the length of the solenoid.The expression for n in term of N, total number of terms…

Q: 3 Induction Coil Solenoid A closed copper coil with 100 turns of wire and a total resistance of R =…

A: Given Data The number of turns of copper coil is:N=100 turns The total resistance is:R=5Ω The…

Q: Shown in the figure below is a generator being used to power a resistor. The generator consists of a…

A:

Q: What inductance (in H) do you need to produce a resonant frequency of 60 Hz, when using a 4.95 µF…

A: f = 60 Hz C = 4.95 uF

Q: • What is the phase angle in an RLC circuit with R = 9.9 kΩ,C = 1.5 mF, and L = 250 mH? The…

A: Phase angle is the angle between voltage and current. It is given by, Given, Therefore,

Q: Design an AM modulation scheme that takes an input message x(t) and creates the transmitted signal…

A: Given: Input signal=x(t) output signal=y(t)=x(t)cos(ωct)

Q: **45 Figure 28-44 shows a 4B wood cylinder of mass m = 0.250 kg and length L = 0.100 m, with N =…

A:

Q: P8 The current carried by a long straight conductor is given as I = 103 A/s-t as a function of time.…

A: Given : Current carried by long conductor, I = 103 A/s Distance between conductor and square loop, L…

Q: cl •2 Figure 29-35a shows an ele- ment of length ds = 1.00 um in a very long straight wire carrying…

A:

Q: What is the inductance of the circuit?

A:

Q: #2 LC Resonance Phenomena A 3.41 µF capacitor and a 0.254 H inductor are connected in series. What…

A: Capacitance, C = 3.41 μF = 3.41 x 10-6 F Inductance, L = 0.254 H

Q: 2) A square loop of side 2 m is located in the plane x = 0 as shown in figure. A nonuniform magnetic…

A:

Q: •6 A capacitor with square plates of edge length L is being discharged by a current of 0.75 A.…

A:

Q: Analyze a series RLC AC circuit for which R = 190 2, L= 0.400 H, C = 22.5 μF, and Vs = (24.0 V) сos…

A:

Q: A television channel is assigned the frequency range from 54.0 MHz to 60.0 MHz. A series RLC tuning…

A:

Q: What value must C have to produce resonance at 30.2 kHz ? An LRC circuit has L = 3.46 mH and R =…

A: GivenL= 3.46 mH =3 ×10-3 HR = 5.40 kΩ = 5.40 × 103 ΩResonance frequency (ν) = 30.2 kHz =30.2 × 103…

Q: 1. Take a look at the phasor diagram. The table shows the resistance R. capacitive reactance XC, and…

A: Determine the impedance of circuit I. Determine the impedance of circuit II. Determine the…

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.