2.51 Water, oil, and salt water fill a tube as shown in Fig. P2.51. Determine the pressure at point I (inside the closed tube). Oil density = 1.20 slugs/ft 1-in. diameter 2-in. diameter 3 ft Salt water, SG= 1.20 (1) 2 ft 4 ft Water Figure P2.51

Q: Define Reliability-based design

A: Reliability-based design- It is defined as a  concept that helps in planning, building, and…

Q: What kind of documentation should be done by the field personnel?

A: Few accurate notes were maintained, and all of the contractor 's correspondence was informal in…

Q: What is hydrological process?

A: Objective: To define hydrological process.   A hydrological process is a part of the Earth's…

Q: What is a pick

A: The term pick may be defined in various ways according to the situation Firstly Pick may defined as…

Q: What are the three parts of a technical section under the CSI Format?

A: CSI stands for Construction Specifications Institute. It is the organization which publishes the…

Q: Describe about the installation of a monitoring well.

A: Monitoring wells:- Monitoring wells are those with small diameter drilled in the ground to…

Q: What are the factors of change order preparation?

A: Change orders are among the most common forms of construction delays, budget overruns, driving scope…

Q: What is susbtainable design?

A: Answer Introduction Sustainable design is defined as these are those that seek to minimize the…

Q: What is the most common use of RFI?

A:

Q: How does USGBC operate?

A: - USGBC is acronym for United States Green Building Council. - USGBC is formed to provide new…

Q: 22-ENGINEERING MANAGEMENT 4. As an engineer manager, how will you manage committees effectively?

A: an engineer manager, following method we would apply for  manage committees effectively :

Q: What instructions are given to the field personnel?

A: - Field personnel is a position of an employee who need to work at non office place, mostly at work…

Q: Define the assumptions of Boussinesq Equtions?

A: This equation is to predict the amount of stress over the material. It predicted the stresses in an…

Q: What are the other sources for change orders?

A: The change order can referred as a variation order, it is a work that has been excluded or added to…

Q: Briefly describe the CSI Specifications?

A: CSI stands for the Construction Specification Institute. CSI has introduced a common format for…

Q: (Figure 1) Express your answer with the appropriate 0 Submit μA 6 a 1₂= 26.268 108 mm Previous…

A:

Q: (b) Design the Beam B-B for the maximum sagging section only. Your design should consider the…

A: L=4.55 mh=22.2 mt=122 mmDL=3.55 kPaLL= 4.55 kPafck= 25.5 Mpafy=472 MpaTo design- 1) Loads2) Design…

Q: Give at least 5 important functions of engineering report in construction/ maintenance management in…

A: Construction management uses various functions for planning, executing and finishing the project.…

Q: Explain sources and types of uncertainity ?

A: A state of uncertainty where some possible outcomes have an undesired effect or significant loss.…

Q: How exactly does one use a report generator, and what precisely is meant by a mock-up report?

A: Using a valid, reliable report generator ensures a clean and consistent availability of information…

Q: Discuss  in  details coagulation

A: Coagulation is defined as the process of converting smaller dissolved solids into larger particles…

Q: What is expert determination?

A: Experts are often assigned by justices and adjudicators in national courts and arbitration…

Q: What do you mean by fail safe design

A: Fail-safe designs are the methods of designs in which various techniques can be used to mitigate…

Q: What is a Two-Envelope System?

A: Explanation- Two Envelope System refers to an optional bid procedure in which the bid is presented…

Q: Can the advantages and disadvantages of various systems of verification be recognized from a point…

A: V- model means Verification and Validation model. Just like the waterfall model the V-Shaped life…

Q: Functional Analysis - complete two the Blackbox model - list sub-functions at list 5 critical…

A: In functional analysis, a Blackbox model is a representation of a system where the internal workings…

Q: 1. Construction companies have the unique problem of trying to deliver complicated projects with…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Is the contractor responsible for subsurface investigation?

A: A contractor is a person or an organization that can take out the tasks for the construction…

Q: What is the PreProposal meeting?

A: Pre-proposal meetins:

Q: When does retention get released?

A: Retention is a percentage normally 5% of the total amount which is approved due to the contractor on…

Q: Define the term Underabsorption of Over-Head?

A: Let’s first understand the definition of overhead: Overhead refers to the continuing business…

Q: What are Frontal Inversions?

A: Inversion is used when metrological inversion of temperature takes place. It is an alteration from…

Q: Why do the Field personnel use BIM?

A: A method of building elements describes the geometric features, spatial orientation, geographic…

Q: Techniques

A: The single sideband technique is a technique which is used for transmitting information like an…

Q: How does the project manager make use of cameras and for what purposes

A: The optical technology like cameras can be used by project manager at site for the effective and…

Q: What is the arch dam?

A: Arch dam: It is a curved concrete dam, convex upstream and resists force acting upon it mainly by…

Q: Wht is design requirements

A: Whatever requirements that somehow a designer should usually have to follow while establishing the…

Q: What exactly is a mock-up report, and how exactly does a report generator do its tasks?

A: A mock-up report is a sample or prototype report that is created to provide a visual representation…

Q: What is Boundary value testing?

A:

Q: What is a boundary value problem? Where did it occur?

A:

Q: What is structural database testing, and how is it distinguished from other types of testing?

A: The 3 types of Database Testing are Structural Testing Functional Testing Non-functional Testing…

Q: 7. of ethics may provide guidance in the decision-making process for engineers. Fill in the blank

A: Principle of Ethics may provide guidance in the decision-making for engineers.

Professional survey

A professional survey is a systematic questionnaire that the target audience fills out online, usually by filling out google forms. Professional surveys can vary in length and format. The data is stored on a website and the testing tool usually provides a certain level of data analysis in addition to a professional expert review. Several professional online survey softwares are present worldwide like, SoGoSurvey, SurveyGizmo, SurveyMonkey, Qualtrics, and so on.