2.3 Design a 48V system using eight 24V PV Modules BEE 24 VDC 24 VDC 10A 2A VDC 24 VDC 10A 10A 20A 24 VDC 24 VDC 24 VDC 24 VDC 10A 10A 10A 10A

Q: what is the minimum voltage? a) 129 kvp b) 14 kVp c) 86 kVp d) 21 kVp e) 10.7 kVp ge ripple

A: Given data, Output voltage VO=150 V. Ripple voltage Vr=14 %.

Q: The EMF and resistor voltage in a series RLC circuit are shown as functions

A:

Q: A 12 V car battery dies not so much because its voltage drops but because chemical reactions…

A: Given,  The voltage of the dead battery, VDB=8 V The voltage of the battery connected through the…

Q: For the network shown in figure (3) calculate the values of the following: Zil, Zi2, Zol, Z2, Ayı,…

A:

Q: Calculate the load resistance (R) if the maximum power supplied to the load resistor Pmax)=50 watts…

A:

Q: Practice Preblem Using the nodal veltaga method de Fermine the carrent I in the ciroult ahoun. 12 V…

A:

Q: A substation has two feeders, Sub Feeder-A have demand at a time is 35 KW and Sub Feeder-B have…

A: Given data, Individual demand is given, Demand on feeder A is 35 KW Demand on feeder B is 42 KW…

Q: 120 V 0.5 A 104 V 0.3 A 7 76 V 0.3 A 28 V 0.3 A 3 4 60 V 60 V 0.5 A 0.5 A 6. RATING 5

A: Given That when primary is connected across 1 and 2, and secondary is connected 3 and 7 the voltage…

Q: refer to the figure below VP . O Rp jXp Ip Rp = 10 ohms Xp = 3 ohms Rs = 5 ohms Xs = 2 ohms Rc jXm…

A: it is asked to find the value of Rc in terms of secondary winding

Q: 6. Example sheet 1 und e 0 Enns 1. A series R-L circuit, R= 30 0. L =0.025 H is supplied by 250 V.…

A:

Q: olve for the voltage drop and the power dissipated across resistance R3 using Nodal Analysis. ww. 34…

A:

Q: 11. Overcharging of a battery can cause. A. Bucking of a lead plates B. Loss of battery electrolyte…

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: 3. A 60 cycles current 2.8+j 0 flows in a series circuit having a resistance of 40 ohms, an…

A:

Q: TASK 3-Y-Y Three phase system The circuit in Figure 1 is a balanced three phase system which has the…

A: Note: Only active power will be available in purely R Load Only Reactive power will be available in…

Q: 3.2 50 b 4.0 Wr C 1002 502 3.0 d 5.0 $250 750 f Figure 23.

A:

Q: Can you help with subparts 11a-11c Consider the electric circuit in the figure below with the…

A:

Q: I 40KVA, 2000/250 V, 5o HZ Single Pase txusforrer has Following Rarameters O Primary and Secondery…

A: Given S = 40 KVA V1 =2000 VV2 =250 VR1 =0.8ΏR2 =0.012Ώ X1 =4 ΏX2 =0.04 ΏRC,H =6006 ΏXM,H = 1666.7 Ώ…

Q: • A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current…

A: The snubber circuit consist of the series connected resistor and the capacitor Given Data: I = 5 uA…

Q: 1. Assume that the circuit shown in Figure 22-2 is connected to a 60-Hz line and has a total current…

A:

Q: om the circuit below, a. Using Thevenin's Theorem, calculate the Eth and Rth at nodes: i. a-b ii.…

A:

Q: 5. Calculate the Secondary voltages of the transformer in figure 2. PRIMARY SECONDARY 150 TURNS…

A:

Q: Explain this delta connected balanced load

A: In this question,  We need to explain delta connected balanced load.

Q: Find the calculated voltage using voltage divided rule(VDR)

A: Let us solve this problem by starting to explain how voltage division rule works and then calculate…

Q: Use the node voltage method to find the fault at node 2. Voltages before fault: V₁ = 8027.1∠0. 685°…

A: before fault, the voltage at node 1 and node 2,

Q: The reading of ammeter A1 is____ A.The reading of ammeter A2 is____ A. The reading of ammeter A3 is…

A:

Q: form the graph based on the values provided, connect the measuring points by means of lines

A: According to the question, we need to form the graph based on the values provided,

Q: 500 2. 5 V 10 kQ

A:

Q: Please answer in typing format

A:

Q: An ammeter with resistance 'RA' is connected in series with a load resistance of 180 Q. The applied…

A: To calculate the % error in the current measurement due to the loading effect of Ammeter.

Q: 3. For the circuit shown in Figure below, TH is triggered reference to each zero cross over point,…

A: Given circuit:Thyristor is triggered reference to zero cross over point,60⁰Asked to calculate…

Q: QUESTION 9 Six PV modules are connected in series to a load. Each module has Voc = 48 V and Isc=3.2…

A:

Q: How will you explain the electrostatic in this electrostatic speaker's schematic diagram

A: It is asked to explain the electrostatic in this electrostatic speaker.

Q: I would like to know the description of method of Wye to Delta transformation and its working…

A:

Q: Find the complex power for each branch and the total complex power for the circuit shown Figure 1.…

A: In the network, Two independent voltage sources and one depended voltage source The independent…

Q: Determina Vo para cada uno de los circuitos dados con la entrada mostrada. Grafica el voltaje de…

A: The output voltage can be calculated by using the state of the diode and by using the kirchhoff's…

Q: 2. Find the current i, iz and iz in the circuit below: 1852 A 2A

A:

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).