2.26 Find the resultant of the two forces acting on the dam. Locate where the line of action of the resultant passes through the bottom of the dam.

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: if the coldworked radius is twenty mm, now what is the radius before being deformed if the ductility…

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: can you make a sketch of the solution

A:

Q: What do you mean by method of section?

A: Methode of the section is used to solve the static equilibrium of the strusses. In this method,…

Q: This answer is incorrect. Can someone else help me solve this again ?

A: given data

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: Briefly write down the  steps on how to generate (sketch) an involu

A: Involute Profile

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: What are the four basic steps of creating a circular shape in perspective? Using any digital medium,…

A:

Q: Introduction for shaper work process please elaborate in 200 words

A: Shaper is a material removal machine of reciprocating type motion, and used for producing flat…

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: The designer should check on the standard shapes and sizes from the supplier of raw material and…

A: Given : Component shapes in which machining has to be done To find : Design rules for machining

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: A 90° elbow shown in Figure 5 (a) is to direct water flow upward at a rate of 50 kg/s. The water is…

A:

Q: Please typing answer only  IENG 302 - Manufacturing Processes: We are reducing the diameter of a…

A: Here I'm going to find all the answers.

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: Is this the only correct option in the question above? I think the question is worded for more than…

A: To elaborate why a sling psychrometer can measure humidity.

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: To make 5 cast iron tool holder as shown in Figure 2 on a one time order, and the inside hole…

A: Die casting and forging involves huge initial machine cost , it is not recommended to go for die…

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: what happened with the 10 in the first equation?

A:

Q: I need answers to this part, thank you.

A: Monodetail Drawing:A monodetail drawing describes single part. This drawing is used for maximum…

Q: Figure A. Rectangular block of steel. Adapted from: https://media.wdscomponents.com/ri-…

A: Given: Workpiece is slimmed using slab milling To find: 4 items need to perform slab milling process

Q: What is its minimum width if it produces 1000 minima?

A: The expression for the dept of the slits is given by the expression, Dsinθ=mλ For the minimum width…

Q: How do you solve parts a,b and c?

A:

Q: Okay I did everything you did but the only thing I didn't do was take away 10 degrees from my…

A:

Q: What are the types of irregular grids ? Support your answers with relevant diagrams

A: An unstructured or irregular grid consists of triangles and quadrilaterals (2D) or tetrahedral,…

Q: You are required to describe thoroughly how the two parts can be fabricated in the workshop so that…

A: The processes involved in making the lamp holder are: Milling Drilling Internal thread cutting…

Q: Seems incorrect setup, can you resolve?

A:

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…