2.2 Air enters a nozzle steadily at 300kPa, 77°C, and 50m/s and leaves at 100kPa and 320m/s. The heat loss from the nozzle is estimated to be 3.2kJ/kg of air flowing. The inlet area of the nozzle is 3 100cm2. Determine: 2. 2.2.1 the exit temperature of air (24.2°C); .2.2 the exit area of the nozzle (39.7cm2). 2.2.3Why is there a heat loss from the nozzle? 2.

2.2 Air enters a nozzle steadily at 300kPa, 77°C, and 50m/s and leaves at 100kPa and 320m/s. The heat loss from the nozzle is estimated to be 3.2kJ/kg of air flowing. The inlet area of the nozzle is 3 100cm2. Determine: 2. 2.2.1 the exit temperature of air (24.2°C); .2.2 the exit area of the nozzle (39.7cm2). 2.2.3Why is there a heat loss from the nozzle? 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hand written not allowed
Steam expands steadily at a constant temperature. The flow rate is 13.6 kg/min with an inlet state of wet steam (water) at 80% quality to a final state of 700C and 2.5 MPa. The change of kinetic energy across the device is 3.5 kJ/kg, and the heat added is 21.81 kW. Determine (a) the enthalpy of conditions 1 &2, (b) the heat transfer in kJ/kg, (c) the work, and (d) the system power.
2. Air enters a 28-cm diameter pipe steadily at 200 kPa and 20°C with a velocity of 5 m/s. Air is heated as it flows, and leaves the pipe at 180 kPa and 40°C. Determine (a) the volume flow rate of air at the inlet, (b) the mass flow rate of air, and (c) the velocity and volume flow rate at the exit. Air 200 kPa 180 kPa 20°C 40°C 5 m/s
8. Air enters a nozzle steadily at 2.21 kg/m³ and 30 m/s and leaves at 0.762 kg/m³ and 180 m/s. If the inlet area of the nozzle is 80 cm², determine the mass flow rate through the nozzle in kg/s.
(Q3) Refrigerant-134a enters a compressor at 240 kPa and 70°C at a rate of 2.05 m³/s and leaves at a pressure of 1000 kPa. The refrigerant experiences a heat loss through the casing to the surrounding at a rate of 3 kJ/kg. The power input to the compressor is 640 kW. Determine (a) the mass flow rate of the refrigerant and (b) the exit temperature. R-134a
Air at 50 kPa, 100 °C and 5 m/s enters a pipe of diameter 14 cm and exits at 180 kPa and 400 °C. Assuming the air is heated as it flows through the pipe and that the diameter of the pipe is the same at both the inlet and outlet. Calculate: a. The volumetric flowrate of air at the inlet and exit of the pipe. b. The mass flowrate of air at the inlet and exit of the pipe. The rate at which heat is supplied to the system in kJ/s. с. Take the characteristic gas constant of air as 287 J/kg/K.
During a reversible process, 2.07 kg/s of gas rejects 336.8 kJ/s of heat isothermally at 24.9°C. For this gas, c, = 2.14 kJ/kg K and c, = 1.62 kJ/kg K. The initial pressure is 552.3 kPa. Determine the work steady flow of the process in hp if APE = 2.8 kJ/s and AKE = 6.5 kJ/s.
The valve connected to a 450-liter insulated tank of air at 250 kPa and 50̊C is opened,allowing the gas to escape until its pressure drops to 120 kPa. An electric heater insidethe tank maintains the temperature at 50̊C. Using variable specific heats, Determine thefollowing:a) The mass of air withdrawn (kg)b) The energy input to the resistor (kJ)
A mass flowrate of 1 Ibm/s of water at 80 F and 70 pisa is mixed with 1 Ibm/s of saturated vapor water at 70 psia in a mixing chamber. During this process 100 Btu/s of heat is lost from the mixing chamber to the surrounding environment. The exiting stream leaves the mixing chamber at 70 psia. In the question that follows, select the answer that is closest to the true value. What is the quality of the exiting stream ?
As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and velocity of 5 ft/s, flows through a hydraulic turbine-generator, and exits at a point z₁ = 140ft below the intake at 19 psia, 45 ft/s, and a specific volume of 0.01602 ft³/lb. The diameter of the exit pipe is 5 ft and the local acceleration of gravity is 32.2 ft/s². Water Value = $i P₁ = 24 psia V₁ = 5 ft/s Z1 Dam /day Generatori Turbine H P2 = 19 psia 22=0.01602 ft³/lb V₂ = 45 ft/s = 5 ft Evaluating the electricity generated at 8.5 cents per kWh, determine the value of the power produced, in $/day, for operation at steady state and in the absence of internal irreversibilities. Water
Question 6 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 450°C, and 80 m/s, and the exit conditions are 10 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine (a) the change in kinetic energy (b) the power output, (c) the turbine inlet area. Answers: (a)-1.95 kJ/kg, (b) 10.2 MW, (c) 0.00447 m² P-10 MPa 7₁-450°C V₁ = 80 m/s STEAM m = 12 kg/s P₂ = 10 kPa 4,-0.92 V₂ = 50 m/s out
Air is compressed in an adiabatic compressor. Inlet and outlet conditions are 120kPa, 30 oC and 20 m/s; 1.4 MPa, 530 oC and 80 m/s. The surrounding air temperature is 25 oC. The inlet cross-sectional area is 0.013 m2. Assume Cp = 1005 J/kgK, R = 287 J/kgK, k = 1.4. Enter the amount of heat loss due to irreversibility resulting from the heat transfer from the compressor in kW (correct up to one decimal place.)