Answered: 2. Which of the following shapes has…

2. Which of the following shapes has slender elements if all of them are used as compression members? All steel is A36. (A) L4x3x1/4 (B) L6x4x5/16 (C) L5×5×7/16 (D) L6x6x1/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the ASD design strength for the A36 plates shown. Use Fy = 248MPA and Fu = 400MPA.

A: Solution: Given data: Fy=248 MPaFu=400 MPa

Q: All values of Stz are by the joint on the part indicated. What is the missing value? ? 0 O-6a²t 4a²t…

A: The given figure;

Q: Compute the available strength of the compression member shown in the figure.

A: flexural buckling strength for the x axis, KxL/rx = 1.5816(12) =121.5 Fe=π2E(KL/r)2…

Q: A steel plate (called cover plate) having cross-sectional dimensions 7.0 in. x 0.49 in. is welded…

Q: For axially loaded steel column, how could you determine that your section is safe? In case of…

A: In order to determine the safety of the steel column section. The stress available in the section is…

Q: Permissible As in sechion to ensure tensile Compute the design strength of beam shown it 420 MPa ,…

A: To find : Design strength

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

Q: in steel, explain effective length factors

A: Effective length factors (K-factor) are used in the analysis and design of steel structures to…

Q: Determining the spacing of a pair of connecting screws (connectors) between the slab and the steel…

Q: Determine the vertical deflection of end A. A downwards deflection is positive, while an upwards…

Q: Determine the type and amount of stress in each member of the truss shown below due to wind load…

A: A truss is an assembly of members such as beams that are connected through nodes and form a rigid…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A: An arrangement of truss is given and it has been asked to determine force in the member BE.

Q: A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location…

A: Consider the diagram shown below. The length of each segment with respective to their centroid is…

Q: A compression member with an effective length of KL = 12 ft is built up from a W shape and a…

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

A: Given data L1 = 95 in. A1 = 0.35 in2 L2 = 130 in. A2 = 0.35 in2 L3 = 30 in.…

Q: Find the lim f6atx) -f(9) for fCx) = Jx - 3

Q: Criteria for a frame: Osupport loads all two force members all multiforce members some two force…

A: Structures called frames are made up of horizontal and vertical elements. The horizontal elements…

Q: choose the W section of 50 ksi steel

Q: W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned…

Q: what is the advantages of SAP and stadd in steel design

A: SAP and STAAD are both software tools which are commonly used in structural engineering for both…

Q: civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3…

Q: Which of the following is the most efficient column section? O Pipe Wide Flange Square tubing O…

A: Brief concept- Column Section- It is a structural member that helps in transferring the compressive…

Q: Find the moment of inertia (Ix, mm²) of the composite shape from the bottom base. Type answer in two…

A: Given:- To find:- From the given question it is required to calculate the moment of inertia from…

Q: Draw S.F.D and B.M.D for part BE of the frame shown in figure below:*

A: applying equilibrium eq and finding reactions

Q: Which of the following statements is NOT correct? O Bolt holes are significant in designing…

Q: 2. The composite section is made up of 5"x3"x1/2" and 6"x4"x1/2" angle bars on 1"x 12" and 1.5"x16"…

A: Given Data:section made up of = 5''×3''×1''2 and 6''×4''×12''…

Q: m alone)? (Assume bending arour

Q: A steel rod of 30 mm diameter is used as a tie member in roof truss. It may be subjected to reversal…

A: Given-

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long,…

A: Given, L = 8 m or 8000 mm A = 14500 mm2

Q: Topic: Basic Formulas Used in Steel Design: (Allowable Stress Design) ASD Problem: A simple beam has…

A: Span, L = 10 m UDL = 20 kN/m Properties of W450x70 A = 8700 mm² bf = 150 mm tf = 15 mm d =450 mm Ix…

Q: Use A992 steel and select a W shape using LRFD. D = 350 k L = 1000 k 35' Strong axis T 10' Figure 4…

A: Span, L = 35 ft Dead load, D = 350 k Live load, L = 1000 k A992 steel; fy = 50 ksi fu = 65 ksi

Q: SF A D B' -B- A SM O Patm h₂ C+

Q: In the given composite structural section determine the quantities placed in the table below. PLACE…

Q: The beam has a cross section shown in the figure. fc’ = 26 MPa, fy = 390MPa, determine the…

A: Given , Compressive strength of the concrete fc'=26 MPa Yield strength of the steel fy=390 MPa Web…

Q: 40 mm 200 mm 40 mm

Q: Pp= 500 k J P, = 1,000 k I Pp= 500 k // Px=1,000 k fixed fixed Check whether a 17 ft W 14 x 211…

A: Given:- The dead load on the column = PD = 500 k The live load on the column = PL = 1000 k The…

Q: 3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

Q: Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19…

A: Answer Let us first calculate the reactions Consider Moment equilibrium at A Dy * 12 = 200 * 10.5…

Q: 135 kN 135 kN 135 kN 135 kN 135 kN 135 kN 135 kN 8 panels at 7.5 m = 60 m Figure P-430 MATHalino…

Q: A column is formed by welding two A36 MC sections back-to- back. The column is 32 feet long. With…

A: Following are the given information. A=6.45 in2, d=10 in bf=3.32 in, x=0.990 in Ix=102 in4, Iy=6.40…

Question

2.
Which of the following shapes has slender elements if all of them are used as
compression members? All steel is A36.
(B) L6x4x5/16
(C) L5x5×7/16
(D) L6*6*1/2
(A) L4×3×1/4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

Step 2: Solution:

Step 3: Continuing,

Step 4: Continuing,

Step 5: Continuing,

Solution

Trending now

This is a popular solution!

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 58. Calculate the nominal axial strength of the column in KN
A steel plate (called a cover plate) having cross-sectional dimensions W2 8.0 in. x 0.7 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 14.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =|
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
List the elements of {xIx is a rolled steel section}.
Plastic stage is when all elements of a steel section is in yielding condition and reaches its utlimate strength before it collapses without lateral torsional buckling. O True O False
Specifically state the shape and size of the structural steel action: W 36 x 182. (Show complete process or explanation in the finding the answer)
Q) for UB 914x305x201, S460 steel, and ALT = 77.5, find bending strength Pb? ((from tables * 220 MPa 215 MPa 205 MPa O ¹176 MPa 208 MPa 202 MPa 188 MPa O
Determine if the sections are Compact, Non-Compact or slender. (Use ASEP steel Handbook) Show complete solution and neat handwriting. W10x12, A242 W10x12, A242 W12x14, A36
I need the answer as soon as possible
aljall dalla E What is the name of the joint shown below? hp
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area? The following W Section were considered for the design: W10x33 W14x38 W8x40 W16x36 W10x39 W8x13 189 KN 1.50 HL B 145 KN 1.50 E + 137 KN 121 KN -3.00 + 12.00 3.00 154 KN + W4x13 W6x9 W10x12 200 KN -1.50 1.50 1 030 T 1.20 +2.40 0.60 L i 0.30
PRINCIPLES OF STEEL DESIGN