2. The maximum amount of solid waste collected per day for one week is presented below. All the solid waste are to be burned at a municipal waste to energy combustion facility at a constant rate of 100 tons/day. What is the required capacity of the storage pit that should be designed to accommodate twice the required daily capacity Day Solid waste col

Q: Anaerobic digestor was designed to process municipal solid waste having the chemical formula of…

A: Lets calculate the amount of methane gas produced per pound of waste placed in digester as follows:…

Q: TABLE 3-4 Typical physical composition of residential MSW excluding recycled materials and food…

A:

Q: stimate the theoretical production of landfill gas (CH4 only) from the degradation of 20.3 kg of…

A: Density of metahne = 0.7177kg/m3We have to determine the theoritical production of landfill gas CH4…

Q: For the particle distribution given in Figure 3.5, calculate the overall efficiency of the cyclone…

A: Diameter (μm) Cumulative % particles less than % particles Removal efficiency from table % 2 0.4…

Q: Disinfection: Graph the following data for the inactivation of a virus using hypochlorous acid…

A: The data for inactivation of a virus using HOCl is as followsThe graph has to be plot and time…

Q: The hydroxide ion concentration in a solution of NaOH is 2.0 x 10-¹ M at 25 °C. What is the pH of…

A: Given data in question  Concentration of NaOH 2×10-1 M To find out  p(H)

Q: The Philippine Toxic and Hazardous Wastes Act places limits on the quantities of toxic substances…

A: Molar mass of chromium, Cr =52 Potassium, K=39.1 Oxygen, O=16

Q: A baghouse that employs a shaker collection method is being designed to remove sawdust particles…

A:

Q: Problem 6-6 (assume the waste is fed to an anaerobic digester, not landfilled). Use the equation…

A: Hope you got the answers, Feel free to ask any queries and doubts. I tried my best to answer the…

Q: Before being put in service, a new distribution reservoir has to be disinfected. The reservoir is…

A: Given:- The diameter of the reservoir = 10 m  The height of the reservoir = 6 m  The quantity of…

Q: A waste water plant treats 28800 m3/day of sewage water of density 1000 kg/m3 and kinematic…

A: Given: Water flow rate, Q = 28800 m3/day Density of water = 1000 kg/m3Th Kinematic viscosity = 10-6…

Q: A single addition of chlorine yields a log kill every 5 minutes.  During a storm, levels in the…

A: Given: Single addition of chlorine yields  = 1 log kill in 5 min. Number is 100000 cells per ml. Nt…

Q: 35 The average daily waste flow from a factory in an industrial estate is 75 m³ of stearic acid…

A:

Q: How many gallons of 12-percent sodium hypochlorite solution are needed to disinfect a reservoir 20…

A: Given data: Hypochlorite strength = 12% Diameter of the reservoir D=20 ft Depth of the reservoir h=6…

Q: 7-2. Estimate the maximum amount (by weight) of material that could be separated for recycling from…

A: physical composition of residential MSW excluding recycled matarials and food wastes discharaed with…

Q: 2. You are asked to design a disinfection system with a capacity of 50,000 L/hr to achieve 3 log…

A: To determine the volume and dimensions of a chlorine contactor without assuming the length and…

Q: What is the volume of a CSTR with no recycling of settled solids and treating 80 m3/day of…

A: The given data in the question are: The wastewater flow rate (Q) = 80 m3/day The value of θx for…

Q: Calculate the distribution storage needed for equalization storage based on the following peak…

A: Let's go through the peak hourly data and find the maximum demand:12. Peak hourly demand at 6 pm:…

Mechanical Processes

In civil engineering, the materials have to undergo a series of manufacturing processes before using them in construction and structural applications. These manufacturing processes form the foundation stone of mechanical processes. Some of the civil engineering materials such as bars, metallic beams, metallic columns, surveying equipment, earthmovers, overhead cranes, structural and construction components, and even cement that is the most fundamental construction component need to undergo different manufacturing processes before they are ready to use. These processes are mechanical.