2. The gage pressure of the air in the tank, as shown in the figure is measured to be 80 KPa. Determine the elevation h in cm of the mercury column. Neglect the effect of the atmosphere. P= 80 KPa oil (sp.gr=0.72) 75 cm. AIR 30 cm WATER Hg (sp gr. 13.6! water

Q: In the drawing operation, technological property weldability is an important parameter. Select one:…

A: Drawing: It is a process in which uses tensile forces is used to stretch metal.

Q: Rolling: A rolling operation is performed on a 5 mm thick sheet of low carbon steel (K=530, n=0.26…

A: Given:To find:

Q: What is the operation of parting?

A: Parting operation

Q: For a particular centered process, you estimate Pp = 0.90.  What is the estimated ppm defective for…

A: Given, Total number of defective items in a sample size,Pp=0.90To calculate-PPM defective for this…

Q: the blanks: the center distance in (cm) of 4 direct contact rolling.cylinders. Cylinders A-D have a…

A:

Q: In the illustration of direct extrusion below, the extrusion force changes as the ram advances in…

A: Extrusion is the process used for creating objects with a fixed cross-sectional profile. The…

Q: Identify the forming process in which the rectangular shape of the cross section is reduced into…

A:

Q: Consider typical characterstics

A: The casting process is used for the various type of large and complex shapes as these shapes are…

Q: Forms of bulk metal forming include all of the following except? Rolling Extrusion Forging Explosion

A:

Q: i still dont think i am getting the full working how you get to 0.32, am going to need to see the…

A: Given Data

Q: (d) In one production line, there is ultrasonic machines (USM) and electro- discharge machines…

A: USM stands for Ultrasonic Machining USM is a mechanical energy based non-traditional machining…

Q: In the 3% error, why is the design acceptable?

A: Given: There are 3% error in the design. And by this error the developed power reduced from 0.556 MW…

Q: How we can measure shear modulus?

A: The earth's material reaction to shear deformation is measured in shear modulus. The ratio of…

Q: Identify the type of forming process in which the material is required to pass repeatedly through…

A: Option c is correct.

Q: An automated blanking and forming line is designed to from 2 mm thick sheet, made from 2024…

A: Given:Material:  Aluminum,  temper   - Elongation at :    - Young’s Modulus: (70 GigaPascals)   -…

Q: In a forming process the diameter of the specimen is 1 cm and its length changes from 50 mm to 60…

A:

Q: G .l DO o e (iv) Dimensionless film thickness is greater 0 ) 0} ) Question 5: As the temperature is…

A: Lubricants are designed to reduce friction between moving parts as well as the passive resistance of…

Q: If you have a Bulk Deformation Process in Metalworking with a product in the Rolling Process that…

A: Solution      Calculate the final width  Using volume consistency we can find the final width

Q: Using the rolling process significant improvement is accomplished in rolled parts in their various…

A: There are two types of rolling processes one is hot rolling and other one is cold rolling but the…

Q: he end of forging-stroke during impression-die forging is forming of O a. die cavities O b. die…

A: Answer - option (b) - die flash The end of forging-stroke during impression-die forging is forming…

Q: Which three of the following are basic bulk deformation processes in metal forming: forging bar…

A: Given,Different metal forming manufacturing process.To Find - which process is bulk deformation…

Q: Name the four basic bulk deformation processes.

A: Given:

Q: Only the answers have been essentailly provided. I need the process to understand the problem to be…

A: The stresses at the 60° (counterclockwise) is obtained as:…

Q: How the forced vibrations can arise?

A: When a body vibrates due to the influence of external periodic force, then this type of vibrations…

Q: How was the shear formula derived?

A: Shear Stress: This is the ratio of force acting per unit area of an object/component.  This is…

Q: Types of Shaper Machines and their outputs in engineering industry.

A: Shaper Machine : Shaper Machine is a reciprocating type of machine which is usually used for…

Q: (a) Figure 1 shows surface roughness and tolerances obtained in Chemical Machining (CM) and…

A: Chemical machining and electrochemical machining

Q: 8.[Short Answer] As shown in this figure, what's the function of inclined plate colored yellow ?

A: Ans : The structure is showing like truss system where five members or links are attached to each…

Q: In a metal forming industry, you are assigned to setup an equipment which is required to reduce the…

A: To reduce the cross-section of a bar from 100x50mm into 75x25 mm various forming processes can be…

Q: Investigate and describe the different types of fluidization. Mention at least two examples of…

A: Fluidization : In the Fluidization process, The solids are caused to behave like a fluid in terms of…

Q: What Fundamental problems occur in finding the resultant Internal normal force?

A: The resultant internal force is defined as the force, which is the result of resisting forces in the…

Q: What is true stress and true strain?

A: To define: True stress True strain Stress: It is defined as the internal resistance developed at a…

Q: If the number of fatigue is smaller than the number of yield, would that be safe or not? and why?…

A: When machine parts are subjected to fluctuating loading it is called an fatigue, repeated or…

Q: Define deformation process

A: Deformation process is the secondary manufacturing process.

Q: What is Direct Measurement?  - Give 3 Instruments for every basic process variables, its description…

A: direct measurement- vernier calipers, coordinate measuring machine and micrometer theses devices are…