2. The force system shown consists of the couple C and the four forces. The resultant of this system is 500 KN.m counter clockwise couple. CE BOARD 2007 20 kN 12 13 Im 80 kN Him B 2.1 Determine the value of P. 2.2 Determine the value ofQ. 2.3 Determine the value of C.

2. The force system shown consists of the couple C and the four forces. The resultant of this system is 500 KN.m counter clockwise couple. CE BOARD 2007 20 kN 12 13 Im 80 kN Him B 2.1 Determine the value of P. 2.2 Determine the value ofQ. 2.3 Determine the value of C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6 m -120 kN- √2 180 KN 5 3 B —-|▬4.5 m▬| 1 t 6 m 1. The vertical reaction @ support C is E. 189.8 2. The axial force acting @ member AD is D. 97.5 E.136.2 F.172.6 3. The axial force acting @ member AB is D. 97.5 E.136.2 F.172.6 4. The actual stress acting @ member AD is_ D. 72.8 E. 166.3 5. The actual stress acting @ member AD is MPa. - D. 72.8 E. 166.3 KN A. 34.3 B.78.4 C. 111.2 D.145.7 KN. A. 206.1 B. 25.7 C. 42.8 KN. A. 206.1 B. 25.7 C. 42.8 MPa. A. 90.8 A. 90.8 B. 114.4 C. 133.6 B. 114.4 C. 133.6
Determine the normal force, shear force, and moment at point C. Take that P = 13 kN and w= 10 kN/m. Part A |-–1.5 n -1.5 m 1.5 m-1.5 m-1.5 m- P I mi Part B Determine the normal force at point C. C Part C Determine the shear force at point C Determine the moment at point C B
5. Given the parallel force system shown. 30 kN 40 kN 20 kN (2.2) (4,2) (4,10) I 5.1 determine the resultant of the force shown. 5.2 Determine the location of the resultant from the x-axis. 5.3 Determine the location of the resultant from the y-axis.
Take that w0 = 3.4 kN/m. 3 m Wo X = ? 1.5 m A) Replace the distributed loading with an equivalent resultant force. F₁ = ? B) Specify its location on the beam measured from point O.
Compute the force in member BD in kN. P1=117 kN, P2=72 kN and x = 7.8 m. Write numerical value only and in 2 decimal places
5-41. The bulk head AD is subjected to both water and soil-backfill pressures. Assuming AD is “pinned" to the ground at A, determine the horizontal and vertical reactions there and also the required tension in the ground anchor BC necessary for equilibrium. The bulk head has a mass of 800 kg. D 0.5 m B 6 m 4 m 118 kN/m A 310 kN/m
2. Determine the reaction at the supports using E= 70 GPa and I = 1,300,000,000 mm^4. Use excel spreadsheet to determine the values of the unknowns. Draw the FBD of the beam with the calculated values of the support reactions. 150 kN 35 kN/m 4.0 m 2.0 m 2.0 m
What is the Maximum moment in kN-m. Given: w1 = 48, w2 = 14, a = 3, b = 3, and c =3. w1 kN/m w2 kN/m am b m ст Previous 43 KAP
Question: Given: a = 0.4 m b=0.1 m F₁ = 800 kN F₂ = 915 kN M₁ = 400 kNm •A 0.7 m 1 m 1) Find the shear force at Point B, VB: B M, 2) Find the bending moment at Point B, MB:
Q2/ Determine the reactions at the supports. Assume B is hinge connected. El is constant .Use Method of Slope Deflcction Equation.(. (P in kN/m)
Question: Given: a = 0.4 m b = 0.1 m F₁ = 800 Kn F₂ = 912 kN M₁ = 400 kNm •A •В 0.7 m 1 m 1) Find the shear force at Point B, VB: 2) Find the bending moment at Point B, MB:
a) Calculate the shear force and bending moment for the beam subjected to a concentrated load as shown in the figure. Then, draw the shear force diagram (SFD) and bending moment diagram (BMD). b) If P = 20 kN and L = 6 m , draw the SFD and BMD for the beam.