5-41. The bulk head AD is subjected to both water andsoil-backfill pressures. Assuming AD is “pinned" to the groundat A, determine the horizontal and vertical reactions there andalso the required tension in the ground anchor BC necessaryfor equilibrium. The bulk head has a mass of 800 kg.D0.5 mB6 m4 m118 kN/m A310 kN/m

Given Data:P1= 236kNP2= 1007.5kNd1=1.33md2= 2.167m

5-41. The bulk head AD is subjected to both water an oil-backfill pressures. Assuming AD is "pinned" to the grour at A, determine the horizontal and vertical reactions there an also the required tension in the ground anchor BC necessa or equilibrium. The bulk head has a mass of 800 kg. D 0.5 m B 6 m 4 m 118 kN/m A 310 kN /m

5-41. The bulk head AD is subjected to both water an oil-backfill pressures. Assuming AD is "pinned" to the grour at A, determine the horizontal and vertical reactions there an also the required tension in the ground anchor BC necessa or equilibrium. The bulk head has a mass of 800 kg. D 0.5 m B 6 m 4 m 118 kN/m A 310 kN /m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 04. Structure ABD shown is supported at pt. B by a 32-mm diameter rod and at pt. A by a 30mm diameter pin used in The rod is connected at pt. B and pt. C by 20mm diameter pins used in a double shear connection. single shear connections. Each of the pins has an ultimate shear strength of 320MN/m2. A concentrated load of P=45 kN acts as shown. Determine the following: c. the normal stress in rod BC d. the shearing stress in the pins at pt. A and B 5.0m 6.50m 1.5pm 4.50m
o) Drow the shear force and moment orce diaprams fore ams. b)Draw the imapinary r egret on the plan immediately to the left ol the C slie and determine the value of your most sip show- to be made in the region in c Draw the normal drawing the picture C and show the maximum stress valuesby calculating. Pii=21KN h = 30 cm A vy 3,5 m 4,5m b= 20cm
Please solve the follow up qestion.
PLEASE ANSWER THIS. Help me
Cross-section of each member is 400 mm2 2 m 19. Determine the normal stress at 2 m member GI. 20. Determine the normal stress at F15m--15m-15m---15m- member BC. 21. Determine the 6KN normal stress at member CJ. 22. Determine the normal stress at member DE.
Determine the moment M in kN-m that must be applied to the beam to create maximum stress of 98 MPa. Where tf = 19 mm and d = 306 mm
Determine the member force on member EJ.
Determine the member forces BC, EF, AE, FD, and BF. State whether the members are in tension or compression.
Ao 2.25 m E pivot point 2.25 m Ex E 3 KN 1.26 m-1.26 m-1.26 m Ey VB C E 1.8 m FOLLOW THIS FORMAT BELOW I WILL UPVOTE 1.8 m Fy Joint E: For FEF: VD Solve for Ey: (1) For FAB: 6 kN E 1.8 m 2.8814, 2.25 1.8 E₁, = 30 kN For FAF: FAB = B B 1.8 m 1.8 m 4 FAF = FEF 30 1.8 2.25 FAB 38.4187 1.8 2.8814 VF = 1 kN 1.8 m FAB = 24 KN (T) ↑ 1.2 m FAF 38.4187 2.25 2.8814 G 1.8(38.4187) 2.8814 FAF = 30 KN (C) с H C 2. Determine the force in each member of the half hip truss shown. State whether each member is in tension of compression. Reaction at G is a roller support. (Ans: FAB = 5.80 KN (C), FAC = 4.20 KN (T), FBC = 0 KN, FCE = 4.20 KN (T), FBE = 1.450 KN (T), FBD = 5.25 KN (C), FDE = 6 KN (C), FDF = 5.25 KN (C), FEF = 7.25 KN (T), FEG = 0 KN, FFG = 6 KN (C)) 10 kN 2.25(38.4187) 2.8814 1.8 m H 10 kN 1.8 m 2.8814, E₁ +F₁ = 10 E, +40 = 10 1.8 D D FEF FEA Reactions: → FEF= SHOW FBD → ΣΕ = 0 ΣΕ = 0 2.25 E,= 30 kN E, +F, -10=0 E, +F, = 10 ΣΜ = 0 F,(1.8)-10(7.2)=0 [1.8F, = 72] F, = 40 KN E = -30 KN E, =…
answer the ff. and draw the fbd
For the given one bay- one story frame; wn=0.5 s, E=30000 MPa, I=3*107 mm4, S= I/c=2.5*105 mm3. Determine u0, the maximum dynamic deformation and maximum bending stress in the column. Neglect damping.
If the reaction of the ballast on the railway tie can be assumed uniformly distributed over the cross-section along the length as shown. Determine the maximum bending stress developed in the tie. The tie rectangular section has a thickness of t = 6 in.