The Bar shown is subjected to a tensile load of 150 kN. If the stress in the middle portion is limited to 160 N/mm², determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 25cm. Young's modulus is given as equal to 2.0 x 105 N/mm².

The Bar shown is subjected to a tensile load of 150 kN. If the stress in the middle portion is limited to 160 N/mm², determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 25cm. Young's modulus is given as equal to 2.0 x 105 N/mm².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 680 psi in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 13 ksi in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 480 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 520 psi in size. (a) Determine the stresses o, Oy, and the magnitude of Ty and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). Answer: (a) ox = psi Oy = psi Txy = psi (b) Op1= psi Op2 = psi Tmax in-plane psi
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 11 MPa in size. (a) Determine the stresses Ox, Oy, and the magnitude of T,xyand show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 600 psi in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 340 psi in size.(a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element.(b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 880 psi in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 740 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Tyy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g. see Figure 12.15 or Figure 12.16). y
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 780 psi in size.(a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element.(b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).