2. (Sag Vertical Curve) An existing highway-railway at-grade crossing is being redesigned as grade separated to improve traffic operations. The railway must remain at the same elevation. The highway is being reconstructed to travel under the railway. The underpass will be a sag curve that has an initial grade of -2% and a final grade of 2%. The PVI of the sag curve will be centered under the railway (a symmetrical alignment). The sag curve design speed is 45 mi/h. How many feet below the railway should the curve PVI be located?

2. (Sag Vertical Curve) An existing highway-railway at-grade crossing is being redesigned as grade separated to improve traffic operations. The railway must remain at the same elevation. The highway is being reconstructed to travel under the railway. The underpass will be a sag curve that has an initial grade of -2% and a final grade of 2%. The PVI of the sag curve will be centered under the railway (a symmetrical alignment). The sag curve design speed is 45 mi/h. How many feet below the railway should the curve PVI be located?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A grade of -3.0% is followed by a grade of +2.1% which intersects at station 10+250 and elevation of 110 m. If the maximum change in grade per 20 m station is 0.20%, determine the following A. Length of parabolic curve that shall connect these two gradelines. B. Elevation of PC. C. Elevation of a point on the curve @ Sta.10+250.
Q6. To help improve the safety of at-grade intersection of two roads, the intersection is being redesigned so that the E-W road will pass underneath the N-S road. Currently the vertical alignment of the E-W road consists of a crest vertical curve joining a 4% upgrade to a 3% downgrade. The existing vertical curve is 138 m long, the PVC of this curve is at station 14+47, and the elevation of the PVC is 477 m. The centerline of the N-S road is at station 15+45. Your job is to find the shortest vertical curve that provides 6.0 m of clearance between the new E-W road and the N-S road.
A highway curve will pass through a railway and grade. The crossing must be at station 4 + 310 and at elevation 220 3.38 m. the initial grade is + 2% and meets a -3% grade at station 4 + 235 at an elevation of 223.38 m. the rate of change must not exceed at 2%. Compute the length of curve, station and elevation of highest point also check if the condition of rate of change is meet.
I need the answer as soon as possible
1) An equal-tangent crest vertical curve has a 50 mi/h design speed. The initial grade is +3%. The high point is at station 33+37.43 and the PVT is at station 37+18.26. What is the elevation difference between the high point and the PVT? 2) A 1400-ft-long sag vertical curve (equal tangent) has a PVC at stateion 115+00 and elevation 750ft. The intial grade is -3.5% and the final grade is +6.5%. Determine the elevation and stationing of the low point, PVI, and PVT. If you could show as many steps taken as possible that would be helpful in me actually understanding how to do the problem. Thanks
A 532m equal tangent crest vertical curve has PVC at Sta 19+284 and at elevation 181m. The initial grade is 3.02% and the final grade is -4.37%. Determine the elevation (m) of PVI.
Two sections of a highway are separated by 800m. The initial grade is +3.0% and the final grade is -1.0% and the elevation is 12m. Determine the curve lengths required for a 120km/hr vertical alignment to connect two highway segments, keeping the connecting grade as small as possible.
6. A 5.1% grade intersects a -1% grade at STA 5+180 at an elevation of 175m. A vertical curve of length 120m is to be run forward from the point of intersection, and a curve of length 80m is to be extended back forming an unsymmetrical curve. Determine the elevation (m) of the curve below PVI. *
A -4% grade line meets another line of +3.2% grade at station 11+ 4O. If a 225-ft parabolic curve connects these grade lines, at what station is the lowest point along the curve located? Your answer
A two-lane highway is being expanded to four lanes with the original highway consisting of the northbound lanes and the new highway carrying the southbound lanes. At one location, the southbound facility crosses over an existing pipeline. The resulting vertical curve needs to be at least 10 feet above the top of the pipeline. The initial grade is -4 and G2 is +2. The design speed for the new highway is 60 mi/hr. (1) Is the length of the design curve greater or less than the required stopping distance? (2) The PVI is at station 425+74 and the elevation is 980 ft. If the pipeline is at station 424+54 and the elevation of the top of the pipeline is 985 ft, is the distance from the curve to the top of pipeline adequate to meet the 10 feet required cover? I recommend drawing the cross-section of the curve including the location of the pipeline when answering this question. Note that instead of clearance from the curve up to the the bottom of the overpass (example in the book), this is…
A crest vertical curve will connect a 1.5% grade to a -3% grade with a design speed of 45 mph. Using the SSD (stopping site distance) criterion, what is the minimum length of the curve?
A grade of -3.6% is followed by a grade of +2.1% which intersects at station 10+256 and elevation of 116 m. If the maximum change in grade per 20 m station is 0.20%, determine the following A. Length of parabolic curve that shall connect these two grade lines. B. Elevation of PC. C. Elevation of a point on the curve @ Sta.10+250.