2. Perform the following steps for the given circuits and define the working region of the BJT's for the all circuits. a) Find the VCE voltage of the circuit given with (a). b) Calculate the change in VC voltage as a percentage of the circuit given with (a), if the value of ß = 60. c) Find the ICmax and ICmin, when the potentiometer has the value of 1MQ and 02, respectively. d) Find the VC voltage, when the potentiometer has the value of 0.5M2. e) When the potentiometer value is increased from 02 to 1M2, what will be the maximum voltage value of the Vc? +22V +12V 4.7kQ ' 9.1kQ 150kO 1MO 470KQ Vout Vout IC VIC VCE B - 180 B = 120 3.3ko 9.1kO (b)

2. Perform the following steps for the given circuits and define the working region of the BJT's for the all circuits. a) Find the VCE voltage of the circuit given with (a). b) Calculate the change in VC voltage as a percentage of the circuit given with (a), if the value of ß = 60. c) Find the ICmax and ICmin, when the potentiometer has the value of 1MQ and 02, respectively. d) Find the VC voltage, when the potentiometer has the value of 0.5M2. e) When the potentiometer value is increased from 02 to 1M2, what will be the maximum voltage value of the Vc? +22V +12V 4.7kQ ' 9.1kQ 150kO 1MO 470KQ Vout Vout IC VIC VCE B - 180 B = 120 3.3ko 9.1kO (b)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please show me how to solve the following practice problems in step by step solution Than you so much!
help me please..................
Q-2: Explain the saturation of a transistor. Find the given unknowns for the figure below. a. Rc. b. Rg c. Rp. d. VCE e. V Also find the voltage V, at cutoff. 12 V 2 mA Rc 7.6 V V B-80 024 V Q-3: Define Lso and lao, How are they related? Find the following f le corresponding to V = +750mv and Va = +5V
need the answer fast please
Design a 15 V Zener regulator for the following conditions: 1) The load current IL ranges from 200 mA to 300 mA.2) The source voltage ranges from 21 V to 25 V. Based on your design results,a) Draw the Zener regulator circuit.b) Calculate the power ratings for both Zener diode and resistor Ri
Q5: An electron drops from specific energy level to ground state (n=1) in hydrogen atom. The energy difference between these two levels is 12.75 eV. Calculate the initial state of the electron and 2 of the emitted radiation. (Ans: n¡ = 4, 972.54 Å) %3D
None
Q3) For the regulator circuit shown in figure below, Vin-15 V, Rs-10 2, Vz-9.1 V, VBE=0.8V, and R=40 2. What are the values of output voltage, input current, the load current, and collector current. 102016 2-8594 Vin R$ Ⓡ R₂ Vout
5. For the following circuit with ideal OPAM and positive saturation voltage Vsat+ = 9V and negative saturation voltage Vsat-=-8V. Find: a. It is a function of V1, in active region and positive and negative saturation regions. b. The current iA in active region and in positive and negative saturation regions. Remember that no current enters the inverting and non-inverting terminals, and also V+ is different from V- when the OPAM is saturated. 10ΚΩ w 1ΚΩ www Va we+ 1A 1ΚΩ 1ΚΩ w 10kQ
3. In a certain n-channel JFET, Ipss= 8 mA and Vp=-4 V. (a) Determine the value of Ves for maximum drain current. (b) Calculate the drain current for VGs=-5 V (c) Calculate the drain current for Ves=-2 V (d) Determine the maximum value of VGs for cut-off condition.
Please solve it.
Q.1) The step-down converter shown below has a pure resistive load of value 10 2. The input supply voltage is Vs=110 V. The switch (SW) can be assumed ideal. For a chopping frequency of value f= 5 kHz and a duty cycle of value 75 %, perform the following: a) Draw the waveforms of the voltages across the load resistance (R), across the switch (SW), and across the diode (D). b) Draw the waveforms of the currents in the load resistance (R), in the switch (SW), and in the diode (D). c) calculate the average value of the load voltage. d) calculate the rms value of the load voltage. e) calculate the power consumed by the load. f) calculate the effective input resistance of the converter. SW Vs D