2. Measure the cross-section for the bending moment Md = 500kNm Mark also the fit of the steels in the cross-section Show also the difference between the guessed d and the final d [mm and %] P 380 * 580 Concrete: C40/50 Steel: A500H Haak: T8 Protective distance: 25mm

2. Measure the cross-section for the bending moment Md = 500kNm Mark also the fit of the steels in the cross-section Show also the difference between the guessed d and the final d [mm and %] P 380 * 580 Concrete: C40/50 Steel: A500H Haak: T8 Protective distance: 25mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in. Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A. (1) (2) Answer: UCIA - in.
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? 50 kN/m 4 m -2.4 m· -x X- TABLE B-3 Properties of I-Beam Sections (S-Shapes): SI Units Flange Axis Y-Y Web X-X spxy Mass Area Width ıdə (wu) Thickness thickness Pl1 = S (10³ mm³) yli^ = 4 (10° mm*) (u) 27.7 27.7 22.1 Designation (10° mm*) (ww) 20.3 (ww) 38.9 („ww) (ww) (ww) 081 158 006 77 622 622 204 1 320 1 220 081 x 019S 4 230 240 34.5 338 × 158 x 149 x 134 007 184 15.7 3930 3 260 247 O'ZE 19.7 320 001 07 6'6E 32.3 006 81 00 I 15 200 149 6'81 15.9 166 937 677 234 019 215 134 181 22.1 090 € 2870 019 18.6 205 33.0 611 22.1 12.7 874 241 17.5 197 61I x 34.0 019 S510 × 143 143 18 200 16300 14 200 12 500 91S 91S 183 23.4 23.4 20.2 20.3 16.8 S69 653 2 700 20.8 228 x 128 x 112 × 98.2 128 112 33.8 34.5 29.5 179 961 2 540 007 194 19.4 80s 508 216 152 162 16.1 533 001 7 1950 12.3 98.2 20.2 12.8 495 6SI 11.4 144 30.2 661 S460 × 104 104 13 200 457 6SI…
The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150 N/mm2, find the diameter of the middle portion and also the length of the middle portion if the total elongation of the rod is to be 0.2mm. consider the young modulus of a steel.
A 76 mm x 76 mm x 6 mm angular section is welded to an 8-mm thick gusset plate as shown. The angular member is A36 steel with Fy = = 248 MPa and Fu = 400 MPa. The electrode used is E60 with Fu = 414 MPa. The cross sectional area of the angle is 929 mm2. L76×76×6 gusset plate 65 mm 125 mm P Compu te the value of P based on the gross area? Determine the value of P based on the net area if the strength reduction coefficient is 0.85? Determine the value of P based on block shear in the gusset plate along the weld?
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget FBD and show me your step Please make sure your answer is correct please
The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150 N/mm2, find the diameter of the middle portion and also the length of the middle portion if the total elongation of the rod is to be 0.2mm. the length of the rod is 40 cm. consider the young modulus of a steel.
Need correctly in neat and clean handwritten solution explaining every steps
a.544mm b.246mm c.634mm d.798mm
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (8B) Brass: a,=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m В 40 mm diameter 1.3 m C Aluminum Brass
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A